AVL3245619 Panasonic Electric Works, AVL3245619 Datasheet - Page 12

• Manufacturer Part Number: AVL3245619
• Description: SWITCH SNAP FS-T ROLLER GOLD SLD
• Manufacturer: Panasonic Electric Works
• Series: AVL3r

Specifications of AVL3245619

• Circuit: SPDT
• Switch Function: On-Mom
• Contact Rating @ Voltage: 0.1A @ 125VAC
• Actuator Type: Lever, Simulated Roller
• Mounting Type: Chassis Mount
• Termination Style: Solder Lug
• Operating Force: 54gf
• Pole Throw Configuration: SPDT
• Switch Function Configuration: N.O./N.C.
• Actuator Style: Simulated Roller Lever
• Current Rating (max): 0.1A
• Ac Voltage Rating (max): 250VVAC
• Dc Voltage Rating (max): 30VVDC
• Contact Material: Gold Clad
• Mechanical Life: 10000000
• Terminal Type: Solder
• Product Height (mm): 24.4mm
• Product Depth (mm): 6.4mm
• Operating Temp Range: -25C to 85C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

NOTES
1.Regarding fastening of switch body
In fastening the switch body, use flat filis-
ter head M2.3 screws, with tightening
torque of not more than 3 kg-cm.To pre-
vent loosening of the screws, it is recom-
mended that spring washers be used with
the screws and adhesive be applied to
lock the screws.
After mounting the switch and making wir-
ing connectors, the insulation distance
between ground and each terminal
should be confirmed as sufficient.
The positioning of the switch should be
such that the pushbutton or actuator for
the switch should not directly apply force
to the operating section in the free condi-
tion.For a pushbutton, the force from the
pushbutton should be applied in a perpen-
dicular direction.
In setting the movement after operation,
the over-travel should be set not less than
70% as a standard.Setting the movement
at less than 70% of O.T.may cause trou-
bles such as mis-contact and welding due
to small contact force of the switch.
Contact
force
N.O.
side
N.C.
side
0
P.T.
specified value
70% of O.T.
O.T. spedified
value
O.T. max.
Usable
area
Stroke
2.Soldering operation
For manual soldering: 60W soldering iron,
soldering completed within 3 seconds; do
not apply force to the terminals.
For automatic soldering tank: 250 C
+482 F
seconds, 350 C
pleted within 3 seconds.
Terminal portions must not be moved in
min.1 minutes after soldering.Also no ten-
sile strength of lead wires should be ap-
plied to terminals.
3.Regarding connector connections
(.110 quick connect terminals)
ceptacle for .110 quick connect terminals
should be used, and the terminals should
be inserted parallel to the receptacle.Con-
sideration should be given to mounting so
that no tensile load is applied to the lead
wires.
4.In making the switch selection
for no interference up to +20% variation of
the standard characteristics values.
5.Environment
a bad influence on contacts are present,
and locations where there is an excessive
amount of siliceous or other abrasive dust
should be avoided.
Consideration should be given to provide
For making connections, a dedicated re-
Locations where corrosive gases having
immersion, completed within 6
+662 F
immersion, com-
6.Cautions regarding use
This subminiatures switch has been de-
signed as a dedicated switch for AC use,
but it can be used for low capacity DC cir-
cuits.
Please select gold-clad contact types
when loads are in the low-level area of
1mA up to 100mA and 5V up to 30V.
For switching of inductive loads (relays,
solenoids, buzzers, etc.), in order to pre-
vent damage to contacts due to the occur-
rence of arcing, an arc absorbing circuit
should be applied
7.Quality check under Actual Loading
Condition
To assure reliability, check the switch un-
der actual loading conditions.Avoid any
situation that may adversely affect switch-
ing performance.
8.When using lever type switch, care
should be taken not to apply undue
force on the body from the opposite
side or side ways to its operating direc-
tion.
AV3,AVM3/AVT3,AVL3
100 mA
1 mA
3 A
0
DC
AC
5
5
Double layer contac type
Triple layer contact type
Au (-64)
15
Au (-61)
Ag
30V
30
250V
89