MCP79410T-I/MNY Microchip Technology, MCP79410T-I/MNY Datasheet - Page 17
![IC RTC/CALENDER 8TDFN](/photos/7/21/72165/c04-129_mn_sml.jpg)
MCP79410T-I/MNY
Manufacturer Part Number
MCP79410T-I/MNY
Description
IC RTC/CALENDER 8TDFN
Manufacturer
Microchip Technology
Type
Clock/Calendar/EEPROMr
Datasheet
1.MCP79410T-IMNY.pdf
(34 pages)
Specifications of MCP79410T-I/MNY
Package / Case
8-WFDFN Exposed Pad
Time Format
HH:MM:SS (12/24 hr)
Date Format
YY-MM-DD-dd
Memory Size
1K (128 x 8)
Interface
I²C, 2-Wire Serial
Voltage - Supply
1.8 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Function
Clock/Calendar
Rtc Memory Size
64 B
Supply Voltage (max)
5.5 V
Supply Voltage (min)
1.8 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Rtc Bus Interface
I2C
Supply Current
400 uA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
MCP79410T-I/MNYTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
5.2
5.2.1
Following the Start condition from the master, the
control code and the R/W bit (which is a logic low) are
clocked onto the bus by the master transmitter. This
indicates to the addressed slave receiver that a byte
with a word address will follow after it has generated an
Acknowledge bit during the ninth clock cycle.
Therefore, the next byte transmitted by the master is
the word address and will be written into the Address
Pointer of the MCP7941X. After receiving another
Acknowledge signal from the MCP7941X, the master
device transmits the data word to be written into the
addressed
acknowledges again and the master generates a Stop
condition. This initiates the internal write cycle, and,
during this time, the MCP7941X does not generate
Acknowledge signals for EEPROM write commands. If
an attempt is made to write to an address and the
protection is set then the device will acknowledge the
command but no write cycle will occur, no data will be
written, and the device will immediately accept a new
command. After a byte write command, the internal
address counter will point to the address location
following the one that was just written.
5.2.2
The write control byte, word address, and the first data
byte are transmitted to the MCP7941X in the same way
as in a byte write. But instead of generating a Stop
condition, the master transmits up to 7 additional bytes,
which are temporarily stored in the on-chip page buffer
and will be written into memory after the master has
transmitted a Stop condition. After receipt of each word,
the three lower Address Pointer bits are internally
incremented by one. If the master should transmit more
than 8 bytes prior to generating the Stop condition, the
address counter will roll over and the data received
previously will be overwritten. As with the byte write
operation, once the Stop condition is received, an
internal write cycle will begin
2010 Microchip Technology Inc.
EEPROM
EEPROM BYTE WRITE
EEPROM PAGE WRITE
memory
location.
(Figure
The
5-4).
MCP7941X
Preliminary
Note:
Note:
Page write operations are limited to writing
Addressing undefined EEPROM locations
bytes within a single physical page,
regardless of the number of bytes actually
being
boundaries start at addresses that are
integer multiples of the page buffer size (or
‘page size’) and end at addresses that are
integer multiples of [page size - 1]. If a
page write command attempts to write
across a physical page boundary, the
result is that the data wraps around to the
beginning of the current page (overwriting
data previously stored there), instead of
being written to the next page as might be
expected. It is therefore necessary for the
application software to prevent page write
operations that would attempt to cross a
page boundary.
will
acknowledging the address.
result
transmitted.
in
MCP7941X
the
MCP7941X
Physical
DS22266A-page 17
page
not