234476 Loctite, 234476 Datasheet - Page 2

• Manufacturer Part Number: 234476
• Description: 3873 SELF SHIM HI COND THREM ADH
• Manufacturer: Loctite
• Series: LOCTITE® 3873™r
• Type: Acrylic Adhesive (Activator Sold Separately)r

Specifications of 234476

• Size / Dimension: 25 ml Syringe
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 1000-103

Heat Aging
Aged at temperature indicated and tested @ 22 °C
GENERAL INFORMATION
For safe handling information on this product, consult the
Material Safety Data Sheet (MSDS).
Where aqueous washing systems are used to clean the
surfaces before bonding, it is important to check for
compatibility of the washing solution with the adhesive. In
some cases these aqueous washes can affect the cure and
performance of the adhesive.
This product is not normally recommended for use on plastics
(particularly thermoplastic materials where stress cracking of
the plastic could result). Users are recommended to confirm
compatibility of the product with such substrates.
Directions for use
Henkel Americas
+949.789.2500
1. For best performance bond surfaces should be clean and
2. To ensure a fast and reliable cure, Activator 7387™
3. The recommended bondline gap is 0.1 mm. Where bond
4. Excess adhesive can be wiped away with organic solvent.
5. Bond should be held clamped until adhesive has fixtured.
Aluminum to G-10 Epoxyglass:
free from grease.
should be applied to one of the bond surfaces and the
adhesive to the other surface. Parts should be assembled
within 15 minutes.
gaps are large (up to a maximum of 0.5 mm), or faster
cure speed is required, Activator 7387™ should be
applied to both surfaces. Parts should be assembled
immediately (within 1 minute).
@ 100 °C
@ 125 °C
@ 50 °C
@ 100 °C
@ 125 °C
175
150
125
100
75
50
25
0
For the most direct access to local sales and technical support visit: www.henkel.com/electronics
0
100 200 300 400 500 600 700 800 900 1000
(psi)
N/mm² 6.5
(psi)
N/mm² 4.2
(psi)
N/mm² 8
(psi)
N/mm² 6.2
(psi)
N/mm² 2.6
(psi)
(1,720)
(940)
(610)
(1,160)
(900)
(380)
+44.1442.278.000
Henkel Europe
Loctite Material Specification
LMS dated May-22, 1998. Test reports for each batch are
available for the indicated properties. LMS test reports include
selected QC test parameters considered appropriate to
specifications for customer use. Additionally, comprehensive
controls are in place to assure product quality and
consistency. Special customer specification requirements may
be coordinated through Henkel Quality.
Storage
Store product in the unopened container in a dry location.
Storage information may be indicated on the product container
labeling.
Optimal Storage: 2 °C to 8 °C. Storage below 2 °C or
greater than 8 °C can adversely affect product properties.
Material removed from containers may be contaminated during
use. Do not return product to the original container. Henkel
Corporation cannot assume responsibility for product which
has been contaminated or stored under conditions other than
those previously indicated. If additional information is required,
please contact your local Technical Service Center or
Customer Service Representative.
Conversions
(°C x 1.8) + 32 = °F
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
µm / 25.4 = mil
N x 0.225 = lb
N/mm x 5.71 = lb/in
N/mm² x 145 = psi
MPa x 145 = psi
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP
Note
The data contained herein are furnished for information only
and are believed to be reliable.
responsibility for the results obtained by others over whose
methods we have no control. It is the user's responsibility to
determine suitability for the user's purpose of any production
methods mentioned herein and to adopt such precautions as
may be advisable for the protection of property and of persons
against any hazards that may be involved in the handling and
use thereof. In light of the foregoing, Henkel Corporation
specifically disclaims all warranties expressed or implied,
including warranties of merchantability or fitness for a
particular purpose, arising from sale or use of Henkel
Corporation’s products. Henkel Corporation specifically
disclaims any liability for consequential or incidental
damages of any kind, including lost profits. The discussion
herein of various processes or compositions is not to be
interpreted as representation that they are free from
domination of patents owned by others or as a license under
any Henkel Corporation patents that may cover such
processes or compositions.
prospective user test his proposed application before repetitive
use, using this data as a guide. This product may be covered
by one or more United States or foreign patents or patent
applications.
6. Product should be allowed to develop full strength before
subjecting to any service loads (typically 24 to 72 hours
after assembly, depending on bond gap, materials and
ambient conditions).
LMS
We recommend that each
TDS 3873™, March-2008
We cannot assume
Henkel Asia Pacific
+86.21.2891.8000