73S8009CN-32IMR/F Maxim Integrated Products, 73S8009CN-32IMR/F Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
73S8009CN-32IMR/F
Manufacturer Part Number
73S8009CN-32IMR/F
Description
IC PWR MGMT/SMART CARD INT 32QFN
Manufacturer
Maxim Integrated Products
Datasheet
1.73S8009CN-DB.pdf
(30 pages)
Specifications of 73S8009CN-32IMR/F
Applications
Smart Card Reader, Writer
Voltage - Supply
3 V ~ 3.6 V
Package / Case
32-VFQFN Exposed Pad
Mounting Type
Surface Mount
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Interface
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
73S8009CN-32IMR/F
Manufacturer:
TERIDIAN
Quantity:
20 000
73S8009CN Data Sheet
6
CLK
Pin
Name
PRES
VCC
GND
Host Processor Interface
CS
OFF
I/OUC
AUX1UC
AUX2UC
SC/USB
DP
Pin
Number
16
14
19
17
12
32
13
25
1
2
3
Type
PSO
GND
IO
IO
IO
IO
O
O
I
I
I
Equivalent
Figure 15
Figure 19
Figure 13
Figure 19
Figure 12
Figure 18
Figure 18
Figure 18
Figure 19
Figure 14
Circuit
–
Card clock: provides clock signal (CLK) to card. CLK
is the pass through of the signal on pin CLKIN.
Internal control logic will hold CLK low when card is
not activated or VCC is too low. Will be tri-stated
when SC/USB is set low.
Smart card Presence switch: Active high indicates
card is present.
Smart card activation will not be permitted unless
PRES is active.
Card power supply – logically controlled by
sequencer, output of LDO regulator. Requires an
external 0.47uF low ESR filter capacitor to GND.
Card ground.
Chip Select. When CS = 1, the control and signal
pins are configured normally. When CS is set low,
CMDVCC%, RSTIN, and CMDVCC# are latched.
I/OUC, AUX1UC, and AUX2UC are set to
high-impedance pull-up mode and do not pass data
to or from the smart card. Signals RDY and OFF are
disabled to prevent a low output and the internal
pull-up resistors are disconnected. Should be tied to
VDD when a single 73S8009CN is used.
Interrupt signal to the processor. Active Low -
Multi-function indicating fault conditions and card
presence. Open drain output configuration – It
includes an internal 20kΩ pull-up to V
disabled in Power down state and CS = 0 modes.
System controller data I/O to/from the card. Includes
an 11kΩ pull-up resistor to V
System controller auxiliary data I/O to/from the card
for synchronous / asynchronous operation mode.
Connection to AUX1 is opened when SC/USB is low.
Includes an 11kΩ pull-up resistor to V
System controller auxiliary data I/O to/from the card
for synchronous / asynchronous operation mode.
Connection to AUX2 is opened when SC/USB is low.
Includes an 11kΩ pull-up resistor to V
Smart Card Interface enable, USB interface disable.
Pin is provided with a weak pull-up.
When high, the 73S8009CN operates in
synchronous / asynchronous operation mode.
When low, CLK, RST I/O, AUX1, and AUX2 are
tri-stated. Pin AUX1 is connected to pin DP and pin
AUX2 is connected to pin DM.
USB D+ connection to / from USB controller.
When SC/USB is set low, this pin is electrically
connected to the AUX1 pin, otherwise it is isolated.
Description
DD.
DS_8009CN_026
DD.
DD.
DD.
Pull-up is
Rev. 1.4