PI3USB10MZEEX Pericom Semiconductor, PI3USB10MZEEX Datasheet - Page 2

• Manufacturer Part Number: PI3USB10MZEEX
• Description: IC USB SWITCH DUAL 2X1 12TDFN
• Manufacturer: Pericom Semiconductor

Specifications of PI3USB10MZEEX

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Maximum Ratings
(Above which useful life may be impaired. For user guidelines, not tested.)
DC Electrical Characteristics for USB 2.0 Switching over Operating Range
(T
Notes:
1.
2.
3.
Power Supply Characteristics (V
Notes:
1.
Parameters
Storage Temperature ...................................................... –65°C to +150°C
Supply Voltage to Ground Potential ............................... –0.5V to +5.25V
DC Input Voltage .............................................................. –0.5V to +5.5V
DC Output Current ........................................................................ 120mA
Power Dissipation ............................................................................. 0.5W
A
Parameter
R
= –40°C to +85°C, V
For max. or min. conditions, use appropriate value specifi ed under Electrical Characteristics for the applicable device type.
Measured by the voltage drop between Y and In pin at indicated current through the Switch-On-Resistance is determined by the lower of the
voltages on the two (Y, In) pins.
For max. or min. conditions, use appropriate value specifi ed under Electrical Characteristics for the applicable device type.
V
FLAT(ON)
I
ΔR
DD
DD
R
V
V
V
I
I
07-0242
IH
ON
IL
IH
IK
IL
ON
= 3.0 - 4.4V, T
Quiescent Power Supply Current
Input HIGH Voltage
Input LOW Voltage
Clamp Diode Voltage
Input HIGH Current
Input LOW Current
Switch On-Resistance
On-Resistance Flatness
On-Resistance match from cen-
ter ports to any other port
A
= 25°C ambient and maximum loading.
DD
Description
= 3.0V – 4.4V)
Description
(3)
DD
(3)
(3)
= 3.0 - 4.4V)
Guaranteed
HIGH level
Guaranteed HIGH level
V
V
V
V
I
V
V
V
I
IN
IN
DD
DD
DD
DD
DD
DD
DD
V
2:1 Mux/DeMux USB 2.0 Switch with Single Select
= –40mA
= -40mA
DD
= Min., 1.25V ≤ V
= Max., I
= Max., V
= Max., V
= Min., V
I
= Min., 1.5V ≤ V
IN
Test Conditions
= Max., V
= -40mA
Test Conditions
2
IN
IN
IN
IN
= –18mA
V
V
@ 1.5V and
IN
= V
= GND
DD
DD
= GND or V
DD
IN
= 4.2V
= 3.3V
Note:
RATINGS may cause permanent damage to the device. This
is a stress rating only and functional operation of the device
at these or any other conditions above those indicated in the
operational sections of this specifi cation is not implied. Ex-
posure to absolute maximum rating conditions for extended
periods may affect reliability.
IN
(1)
≤ V
≤ V
4.2V, Wide Bandwidth, 2-Channel,
(1)
DD
Stresses greater than those listed under MAXIMUM
DD,
,
DD
Min.
2.0
1.6
Min.
Typ.
Typ.
-0.7
4.0
1.0
0.9
(2)
PS8799F
PI3USB10M
Max.
-1.2
0.8
6.5
2.0
Max.
±5
±5
800
Units
Units
μA
Ω
V
μA
11/02/07