PI3USB10LP-AZLEX Pericom Semiconductor, PI3USB10LP-AZLEX Datasheet - Page 2

• Manufacturer Part Number: PI3USB10LP-AZLEX
• Description: IC USB SWITCH DUAL 2X1 10TQFN
• Manufacturer: Pericom Semiconductor

Specifications of PI3USB10LP-AZLEX

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Maximum Ratings
(Above which useful life may be impaired. For user guidelines, not tested.)
DC Electrical Characteristics for USB 2.0 Switching over Operating Range
(T
Notes:
1.
2.
3.
Power Supply Characteristics (V
Notes:
1.
Parameters
Storage Temperature ......................................................–65°C to +150°C
Supply Voltage to Ground Potential .................................–0.5V to +4.6V
DC Input Voltage ..................................................... –0.5V to V
DC Output Current ........................................................................120mA
Power Dissipation .............................................................................0.5W
A
Paramenter
R
= –40°C to +85°C, V
For max. or min. conditions, use appropriate value specifi ed under Electrical Characteristics for the applicable device type.
Measured by the voltage drop between D and D
voltages on the two (D, D
For max. or min. conditions, use appropriate value specifi ed under Electrical Characteristics for the applicable device type.
V
FLAT(ON)
I
ΔR
CC
CC
R
V
V
V
I
I
07-0096
IH
ON
IL
IH
IK
IL
ON
= 3.0 - 4.4V, T
Quiescent Power Supply Current
Input HIGH Voltage
Input LOW Voltage
Clamp Diode Voltage
Input HIGH Current
Input LOW Current
Switch On-Resistance
On-Resistance Flatness
On-Resistance match from cen-
ter ports to any other port
A
= 25°C ambient and maximum loading.
CC
n
) pins.
Description
= 3.0 - 4.4V)
Description
(3)
CC
(3)
(3)
= 3.0 - 4.4V)
n
pin at indicated current through the Switch On-Resistance is determined by the lower of the
Guaranteed
HIGH level
Guaranteed HIGH level
V
V
V
V
I
V
I
V
I
INPUT
INPUT
INPUT
CC
CC
CC
CC
CC
CC
V
CC
= Max., I
= Max., V
= Max., V
= Min., -0.4V ≤ V
= Min., -0.4V ≤ V
= Min., -0.4V ≤ V
= –40mA
= Max., V
= -40mA
= -40mA
Test Conditions
USB 2.0 High-Speed (480 Mbps) Signal Switch
Test Conditions
CC
2
+0.5V
SEL
Targeted for Battery Powered Applications
SEL
SEL
SEL
V
V
= –18mA
= VCC
= GND
CC
CC
= GND or V
= 4.2V
= 3.3V
input
input
input
Note:
RATINGS may cause permanent damage to the device. This
is a stress rating only and functional operation of the device
at these or any other conditions above those indicated in the
operational sections of this specifi cation is not implied. Ex-
posure to absolute maximum rating conditions for extended
periods may affect reliability.
(1)
(1)
≤ 1.0V
≤ 1.0V,
≤ 1.0V,
Stresses greater than those listed under MAXIMUM
CC
,
Min.
Min.
1.8
1.6
Typ.
Typ.
-0.7
5.5
1.5
0.9
PI3USB10LP-A
(2)
PS8858G
Max.
Max.
-1.2
0.8
6.5
2.0
±5
±5
1
Units
Units
μA
V
Ω
05/02/07
A