E3Z-R86 Omron, E3Z-R86 Datasheet - Page 20

• Manufacturer Part Number: E3Z-R86
• Description: Industrial Photoelectric Sensors Retro Wide View PNP Connector
• Manufacturer: Omron
• Type: Photoelectric Sensorr

Specifications of E3Z-R86

• Features: Light ON / Dark ON
• Height: 20 mm
• Length: 43.5 mm
• Maximum Operating Temperature: + 55 C
• Minimum Operating Temperature: - 25 C
• Operating Supply Voltage: 12 V to 24 V
• Width: 10.8 mm
• Sensing Distance: 4000 mm
• Output Configuration: PNP
• Svhc: No SVHC (15-Dec-2010)
• Sensing Range Max: 4m
• Sensor Input: Optical
• Supply Voltage Dc Max: 24VDC
• Approval Bodies: CE
• Approval Category: UL Recognised
• Connector Type: M8 Connector
• Current: RoHS Compliant
• Output Current: 100mA
• Output Type: Connector
• Response Time: 1ms
• Rohs Compliant: Yes
• Sensing Range: 4m
• Sensor Output: PNP Open Collector
• Supply Voltage Range Dc: 12V To 24V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: E3ZR86OMS

Precautions
Do not connect an AC power supply to the Sensor. If AC pow-
er (100 VAC or more) is supplied to the Sensor, it may ex-
plode or burn.
Be sure to abide by the following precautions for the safe op-
eration of the Sensor.
Wiring
Power Supply Voltage and Output Load Power Supply Volt-
age
Make sure that the power supply to the Sensor is within the
rated voltage range. If a voltage exceeding the rated voltage
range is supplied to the Sensor, it may explode or burn.
Load Short-circuiting
Do not short-circuit the load, otherwise the Sensor may be
damaged.
Connection without Load
Do not connect the power supply to the Sensor with no load
connected, otherwise the internal elements may explode or
burn.
Operating Environment
Do not use the Sensor in locations with explosive or flamma-
ble gas.
Design
Power Reset Time
The Sensor is ready to operate 100 ms after the Sensor is
turned ON. If the load and Sensor are connected to indepen-
dent power supplies respectively, be sure to turn ON the Sen-
sor before supplying power to the load.
Wiring
Avoiding Malfunctions
If using the Photoelectric Sensor with an inverter or servomo-
tor, always ground the FG (frame ground) and G (ground) ter-
minals, otherwise the Sensor may malfunction.
Mounting
Mounting the Sensor
20
• If Sensors are mounted face-to-face, make sure that the op-
• Always install the Sensor carefully so that the aperture an-
tical axes are not in opposition to each other. Otherwise,
mutual interference may result.
gle range of the Sensor will not cause it to be directly ex-
posed to intensive light, such as sunlight, fluorescent light,
or incandescent light.
Correct Use
Caution
M8 Connector
Distance setting models E3Z-LS
• Do not strike the Photoelectric Sensor with a hammer or
• Use M3 screws to mount the Sensor.
• When mounting the case, make sure that the tightening
• Always turn OFF the power supply to the Sensor before
• Hold the connector cover to connect or disconnect it.
• Secure the connector cover by hand. Do not use pliers, oth-
• If the connector is not connected securely, it may be discon-
• Make sure that the sensing side of the Sensor is parallel
• If there is a mirror-like object below the Sensor, the Sensor
any other tool during the installation of the Sensor, or the
Sensor will lose its water-resistive properties.
torque applied to each screw does not exceed 0.54 Nm.
connecting or disconnecting the metal connector.
erwise the connector may be damaged.
nected by vibration or the proper degree of protection of the
Sensor may not be maintained.
with the surface of the sensing objects. Normally, do not in-
cline the Sensor towards the sensing object.
If the sensing object has a glossy surface, however, incline
the Sensor by 5° to 10° as shown in the illustration, provided
that the Sensor is not influenced by background objects.
may not operate stably. Therefore, incline the Sensor or
separate the Sensor from the mirror-like object as shown
below.
Sensing object
Mirror-like object
Surface of sensing object
Sensing side
Glossy object
Photoelectric Sensors