MOC3011M Fairchild Semiconductor, MOC3011M Datasheet - Page 6
![Triac & SCR Output Optocouplers DIP-6 NON-ZERO TRIAC](/photos/15/83/158322/dip006_sm_-angle_sml.jpg)
MOC3011M
Manufacturer Part Number
MOC3011M
Description
Triac & SCR Output Optocouplers DIP-6 NON-ZERO TRIAC
Manufacturer
Fairchild Semiconductor
Datasheet
1.MOC3011M.pdf
(11 pages)
Specifications of MOC3011M
Configuration
1
Maximum Input Current
60 mA
Maximum Operating Temperature
+ 85 C
Maximum Power Dissipation
330 mW
Maximum Reverse Diode Voltage
3 V
Minimum Operating Temperature
- 40 C
Output Type
AC
Package / Case
PDIP White
Typical Input Voltage
1.15 V
Zero-crossing Circuit
No
Output Device
Triac
Isolation Voltage
5300 Vrms
Peak Output Voltage (vdrm)
250 V
Maximum Input Voltage
1.5 V
Maximum Output Voltage
175 VAC
Minimum Trigger Current
10 mA (Max)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
MOC3011M_NL
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MOC3011M
Manufacturer:
FAIRCHIL
Quantity:
844
Part Number:
MOC3011M
Manufacturer:
FAIRCHILD/仙童
Quantity:
20 000
©2005 Fairchild Semiconductor Corporation
MOC301XM, MOC302XM Rev. 1.0.2
Note:
This optoisolator should not be used to drive a load directly. It is intended to be a trigger device only.
400V (MOC302X)
250V (MOC301X)
APPLIED VOLTAGE
0 VOLTS
WAVEFORM
Vdc
PULSE
INPUT
RC
252 V (MOC302X)
158 V (MOC301X)
MERCURY
WETTED
RELAY
V
R
V
CC
CC
TEST
R
R
Figure 5. Static dv/dt Test Circuit
in
in
Figure 7. Inductive Load with Sensitive Gate Triac (I
C
TEST
1
1
D.U.T.
D.U.T.
2
3
2
3
MOC3010M
MOC3011M
MOC3012M
MOC3010M
MOC3011M
MOC3012M
R = 10 k
Figure 6. Resistive Load
V max =
dv/dt =
SCOPE
PROBE
X100
= 250 V (MOC301X)
400 V (MOC302X)
0.63 V max
6
RC
6
5
4
6
5
4
1. The mercury wetted relay provides a high speed
2. 100x scope probes are used, to allow high
3. The worst-case condition for static dv/dt is
180
=
=
180
repeated pulse to the D.U.T.
speeds and voltages.
established by triggering the D.U.T. with a normal
LED input current, then removing the current. The
variable R
increased until the D.U.T. continues to trigger in
response to the applied voltage pulse, even after
the LED current has been removed. The dv/dt is
then decreased until the D.U.T. stops triggering.
0.1 F
252
158
RC
RC
RC
is measured at this point and recorded.
(MOC302X)
(MOC301X)
R
C1
L
TEST
2.4k
GT
allows the dv/dt to be gradually
15 mA)
Z
120 V
60 Hz
L
120 V
60 Hz
www.fairchildsemi.com