UM232R FTDI, UM232R Datasheet - Page 24

• Manufacturer Part Number: UM232R
• Description: Interface Modules & Development Tools USB to Serial UART Dev Mod for FT232R
• Manufacturer: FTDI
• Type: Development Moduler

Specifications of UM232R

• Interface Type: USB, Serial, UART
• Data Bus Width: Serial
• Operating Supply Voltage: 1.8 V to 5.25 V
• Product: Interface Modules
• Supported Devices: FT232R
• Svhc: No SVHC (18-Jun-2010)
• Development Tool Type: Development Kit
• Kit Features: Single Chip USB To Asynchronous Serial Data Transfer Interface, Auto Transmit Buffer
• Rohs Compliant: Yes
• Supported Families: FT232RL
• Features: Single Chip USB To Asynchronous Serial Data Transfer Interface, Auto Transmit Buffer Control
• Tool / Board Applications: USB To
• For Use With/related Products: FT232R
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

9
Following a power-on reset or a USB reset the FT232R will scan its internal EEPROM and read the USB
configuration descriptors stored there. The default values programmed into the internal EEPROM in the
FT232RL used on the UM232R are shown in Table 8.1.
Parameter
USB Vendor ID (VID)
USB Product UD (PID)
Serial Number Enabled?
Serial Number
Pull down I/O Pins in USB
Suspend
Manufacturer Name
Product Description
Max Bus Power Current
Power Source
Device Type
USB Version
Remote Wake Up
High Current I/Os
Load VCP Driver
CBUS0
CBUS1
CBUS2
CBUS3
CBUS4
Invert TXD
Invert RXD
Invert RTS#
Invert CTS#
Invert DTR#
Invert DSR#
Invert DCD#
Invert RI#
Table 9.1 Default Internal EEPROM Configuration
© Copyright 2009 Future Technology Devices International Ltd
Internal EEPROM Configuration
UM232R USB <->
UM232R USB - Serial UART Development Module Incorporating Clock Generator
Bus Powered
See Note
PWREN#
PWREN#
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
TXLED#
RXLED#
Enabled
Enabled
SLEEP#
FT232R
100mA
0403h
6001h
Value
Serial
0200
FTDI
Yes
Notes
FTDI default VID (hex)
FTDI default PID (hex)
A unique serial number is generated and programmed into
the EEPROM during final test of the UM232R module.
Enabling this option will make the device pull down on the
UART interface lines when the power is shut off (PWREN#
is high).
Returns USB 2.0 device description to the host. Note: The
device is be a USB 2.0 Full Speed device (12Mb/s) as
opposed to a USB 2.0 High Speed device (480Mb/s).
Taking RI# low will wake up the USB host controller from
suspend.
Enables the high drive level on the UART and CBUS I/O
pins.
Makes the device load the CVP driver interface for the
device.
Default configuration of CBUS0 – Transmit LED drive.
Default configuration of CBUS1 – Receive LED drive.
Default configuration of CBUS2 – Power enable. Low after
USB enumeration, high during USB suspend.
Default configuration of CBUS3 – Power enable. Low after
USB enumeration, high during USB suspend.
Default configurations of CBUS4 – Low during USB
suspend.
Signal on this pin becomes TXD# if enable.
Signal on this pin becomes RXD# if enable.
Signal on this pin becomes RTS if enable.
Signal on this pin becomes CTS if enable.
Signal on this pin becomes DTR if enable.
Signal on this pin becomes DSR if enable.
Signal on this pin becomes DCD if enable.
Signal on this pin becomes RI if enable.
Document Reference No.: FT_000051
Clearance No.: FTDI# 125
Datasheet Version 1.04
23