II-EVB-363MW-US-110 Connect One, II-EVB-363MW-US-110 Datasheet - Page 6
![WiFi / 802.11 Modules & Development Tools Nano WiReach Eval Board-US](/photos/15/98/159871/evb363_sml.jpg)
II-EVB-363MW-US-110
Manufacturer Part Number
II-EVB-363MW-US-110
Description
WiFi / 802.11 Modules & Development Tools Nano WiReach Eval Board-US
Manufacturer
Connect One
Datasheet
1.II-EVB-363MW-US-110.pdf
(27 pages)
Specifications of II-EVB-363MW-US-110
Interface Type
RS-232, USB
Security
64/128 bit WEP, AES-CCM, TKIP, WPA, WPA2
Operating Voltage
9 VDC
Antenna
External
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Connect One
6.
To test the wireless LAN connection, you need to configure the Nano LANReach for
your LAN:
To test the connection, use the iChipConfig utility to perform any activity that
requires network connection such as retrieving a web page, sending an email, or
II-EVB-363NW User’s Manual
5. Enter the AT+iRP11 command to obtain a report of all the Access Points
6. Enter AT+iWLSI=<ssid>. ssid is the ID of the Access Point you connect to.
7. If you want to enable WEP encryption, configure the following parameters:
8.
9.
At this stage a connection to the Access Point should be established. Verify that
the Nano WiReach has received an IP address from the DHCP server by issuing
the AT+iIPA? command. The Nano WiReach should reply with I/<IP address>.
To test the connection, use the iChipConfig utility to perform any activity that
requires network connection such as retrieving a web page, sending an email, or
opening a socket. You may also try to PING the iChip from another station on the
network.
1. Connect the Nano LANReach module to the LAN network.
2. Start the iChipConfig Utility on your PC.
3. In the main window of the utility, click the Dumb Terminal icon.
4. In the Dumb Terminal window, enter the AT+i command to verify that the
5. Configure the LANReach module IP address in the +iDIP parameter. Set
6. Set +iDIP to an IP address to skip the DHCP process and use a fixed IP. In this
7.
COM port. When using a USB connection, select the USB virtual COM being
used.
available in your area.
Note that ssid is a case-sensitive string.
• AT+iWLWM=<n>
• AT+iWLKI=<n> where n is the WEP key index (n=1..4)
• AT+iWLK<n>=<keyString>
If you want to enable WPA encryption, configure the following parameter:
AT+iWLPP=<passphrase>
be used in generating the WPA1-PSK encryption key. It is normal for the
iChip to take a few moments before returning I/OK in this case.
Enter AT+iDOWN in order to reset the Nano WiReach and connect to the
WiFi network.
Testing the Nano LANReach LAN Connection
iChip is communicating with your PC. You should receive an I/OK in
response. If this has failed, click the “Setup Port” button and select the correct
COM port. When using a USB connection, select the USB virtual COM being
used.
AT+iDIP=0.0.0.0 if you want the LANReach to receive IP settings for the
network’s DHCP server.
case you should also define the +iSNET (subnet) parameter. For example,
AT+iSNET=255.255.255.0
Enter AT+iDOWN in order to reset the Nano WiReach and connect to the
LAN network.
key, and n=2 means 128-bit key
keyString is the WEP key string in the n
where n=0 means no security, n=1 means 64-bit
where n is an index between 1 and 4, and
where passphrase is the pass-phrase to
th
position.
6