RX6001 RFM, RX6001 Datasheet
RX6001
Specifications of RX6001
Available stocks
Related parts for RX6001
RX6001 Summary of contents
Page 1
... The RX6001 employs RFM’s amplifier-sequenced hybrid (ASH) architecture to achieve this unique blend of characteristics. All critical RF functions are contained in the hybrid, simplifying and speeding design-in. The RX6001 is sensitive and stable. A wide dynamic range log detector, in combination with digital AGC and a compound data slicer, provide robust performance in the presence of on-channel interference or noise ...
Page 2
... Maximum Units dB dB µA 3.7 Vdc mV 10 P-P 85 ° Inches Min Nom Max .389 .395 .400 .265 .270 .275 .070 .076 .080 .065 .070 .075 .015 .020 .025 .035 .040 .045 .125 .130 .135 .055 .060 .065 Page RX6001 - 4/7/08 ...
Page 3
... K ±1%, typical values 160 K K 4.7 µ ±5% NPO ohm antenna 100 nH 50 ohm antenna R TH1 R 12 TH2 THLD 2 RREF 11 R REF GND2 10 LPF ADJ 9 R LPF Data Output Notes ±5% ±5% ±5% ±1% ±5% ±5% tantalum Page RX6001 - 4/7/08 ...
Page 4
... RFA1 is ON (up to 50%). Since an amplifier-sequenced receiver is inherently a sampling SAW SAW Filter RFA1 Delay Line P1 Pulse Generator RF Data Pulse t PRI t PRC Figure 1 (RFA1 duty factor), where the 10 Detector & Data RFA2 Low-Pass Out Filter P2 Page RX6001 - 4/7/08 ...
Page 5
... CMPIN by separate series coupling capacitors. The AGC reset function is driven by the signal applied to CMPIN. BBOUT DS2 Ref Peak BB Detector BBO dB Below PKDET 4 Peak Thld C PKD AGC DS1 Ref Thld Threshold Control THLD1 THLD2 R R TH1 TH2 R REF AND RXDATA 7 Page RX6001 - 4/7/08 ...
Page 6
... When the operating temperature is limited to 60 oC, the time required to switch from sleep to receive is dramatically less for short sleep times, as less charge leaks away from the BBOUT- CMPIN coupling capacitor. can be adjusted PW1 ). The total turn-on time to Page RX6001 - 4/7/08 ...
Page 7
... LPF in kilohms user selected LPF in µ user selected BBO is given kilohms set PW2 is in kilohms PW , where f is LPF LPF = 1.21*R , where LPF Notes PKD Page RX6001 - 4/7/08 ...
Page 8
... BBO PKD and 1.5* t PKA For this case: MAX BBO LPF from 4.5 kHz to 1.8 MHz. LPF is in kHz LPF AGC AGH with variations PKA for internal BBO and BBC between this pin and and 1.3* f LPF LPF Page RX6001 - 4/7/08 ...
Page 9
... RF amplifier). The ON pulse width t PW2 - 18.6, where µs and R PW1 PW1 PW to RREF. The threshold is TH1 can be adjusted between 0.1 and PRI is given by kilohms is in kilohms with a resistor R to ground (the ON pulse PW1 kilohms TH2 from start-to-start PRC PW1 is given by: PW Page RX6001 - 4/7/08 ...
Page 10
... E-mail: info@rfm.com ©2008 by RF Monolithics, Inc. .435 0.000 Dimensions in inches. SM-20H PCB Pad Layout Note: Specifications subject to change without notice. .370 .345 .305 .265 .225 .185 .145 .105 .09 .065 RX6001 - 4/7/08 Page ...