EXC-24CN601X Panasonic, EXC-24CN601X Datasheet - Page 4

• Manufacturer Part Number: EXC-24CN601X
• Description: EMI/RFI Suppressors & Ferrites 2 MODE 600Ohms NOISE FILTER
• Manufacturer: Panasonic

Specifications of EXC-24CN601X

• Shielding: Unshielded
• Test Frequency: 100 MHz
• Product: Ferrite Beads
• Impedance: 600 Ohms
• Tolerance: 25 %
• Maximum Dc Current: 200 mAmps
• Maximum Dc Resistance: 0.9 Ohms
• Package / Case: 0504 (1210 metric)
• Termination Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

■
■
Recommendations and precautions are described below.
<Repair with hand soldering>
● Preheat with a blast of hot air or similar method. Use a soldering iron with a tip temperature of 350 °C or less. Solder
● Never touch this product with the tip of a soldering iron.
The following are precautions for individual products. Please also refer to the common precautions shown on page 4
of this catalog.
1. Use rosin-based fl ux or halogen-free fl ux.
2. For cleaning, use an alcohol-based cleaning agent. Before using any other type, consult with our sales person
3. Do not apply shock to 2 mode Noise Filters (hereafter called the fi lters) or pinch them with a hard tool (e.g. pli-
4. Store the fi lters in a lo ca tion with a temperature ranging from −5 °C to +40 °C and a relative humidity of 40 % to 60 %,
5. Use the fi lters within half a year after the date of the outgoing inspection indicated on the packages.
Design and specifi cations are each subject to change without notice. Ask factory for the current technical specifi cations before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Safety Precautions
Recommended Land Pattern Design
Recommended Soldering Conditions
● Recommended soldering conditions for refl ow
● Flow soldering
each electrode for 3 seconds or less.
in advance.
ers and tweezers). Otherwise, their bodies may be chipped, affecting their performance. Excessive me chanical
stress may damage the fi lters. Handle with care.
where there are no rapid changes in temperature or humidity.
· Refl ow soldering shall be performed a maximum of
· Please contact us for additional information when
· Please measure the temperature of the terminals
· We do not recommend fl ow soldering , because fl ow soldering may cause bridges between the electrodes.
two times.
used in conditions other than those specifi ed.
and study every kind of solder and printed circuit
board for solderability be fore ac tu al use.
Preheating
Peak
E
Time
B
F
E
Heating
– 240 –
For soldering (Example : Sn-37Pb)
For lead-free soldering (Example : Sn/3Ag/0.5Cu)
Preheating
Main heating
Peak
Preheating
Main heating
Peak
140 °C to 160 °C
150 °C to 170 °C
C
D
Dimension (mm)
A
B
E
F
Above 200 °C
Above 230 °C
Temperature
Temperature
max. 260 °C
235 ± 10 °C
1.50 to 1.90
0.50 to 0.70
2 mode Noise Filters
1.10
0.50
0.40
0.30
60 s to 120 s
60 s to 120 s
30 s to 40 s
30 s to 40 s
max. 10 s
max. 10 s
Time
Time
00
Sep. 2010