BLM18BB750SH1D Murata, BLM18BB750SH1D Datasheet - Page 19
![EMI/RFI Suppressors & Ferrites 0603 75ohms HiSpeed Signal Line Tape](/photos/16/33/163388/lpmuratablm_sml.jpg)
BLM18BB750SH1D
Manufacturer Part Number
BLM18BB750SH1D
Description
EMI/RFI Suppressors & Ferrites 0603 75ohms HiSpeed Signal Line Tape
Manufacturer
Murata
Series
BLM Br
Datasheet
1.BLM18BD252SH1D.pdf
(46 pages)
Specifications of BLM18BB750SH1D
Shielding
Unshielded
Test Frequency
100 MHz
Product
Chip Ferrite Beads
Impedance
75 Ohms
Tolerance
25 %
Maximum Dc Current
200 mAmps
Maximum Dc Resistance
0.35 Ohms
Operating Temperature Range
- 55 C to + 125 C
Package / Case
0603 (1608 metric)
Termination Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
BLM18BB750SH1D
Manufacturer:
AD
Quantity:
1 100
Company:
Part Number:
BLM18BB750SH1D
Manufacturer:
MURATA
Quantity:
240 000
2
!Note
!Note
<Unless otherwise specified>
1. Electrical Performance
2. Mechanical Performance
18
No.
No.
Specifications and Test Methods
1
2
3
4
1
2
3
4
Test and Measurement Conditions
Temperature: Ordinary Temp. 15 to 35 C
Humidity: Ordinary Humidity 25 to 85%(RH)
Specifications
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
Capacitance (Cap.)
Insulation Resistance
(I.R.)
Withstanding Voltage
DC Resistance (Rdc 1, 2)
Appearance and
Dimensions
Solderability
Resistance to
soldering heat
Bonding Strength
Item
Item
Meet rating table above.
Products should not be damaged.
Meet rating table above.
Meet dimensions.
Electrodes should be at least 90%
covered with new solder coating.
Meet Table 1.
Table 1
The electrodes should show no failure after testing.
Cap. Change
Appearance
Rdc 1, 2
I.R.
22 to 2200pF
Specifications
Specifications
22000pF
Meet rating table above.
within
No damage
7.5%
0.05 max.
0.5 max.
<In case of doubt>
Temperature: 20 2 C
Humidity: 60 to 70%(RH)
Atmospheric pressure: 86 to 106kPa
Frequency
Voltage: 1 0.2Vrms
Voltage: Rated Voltage
Charging Time: 2 minutes max.
Test Voltage: 150Vdc
Testing Time: 1 to 5s
Charge/Discharge Current: 50mA max.
Measured with 100mA max.
Rdc 1: between signal terminals
Rdc 2: between ground terminals
Visual Inspection and measured with Slide Calipers.
Flux: Ethanol solution of rosin, 25wt%
Pre-heat: 150 5 C, 60 5s
Solder: (1) Sn/Pb = 60/40
Solder Temperature: (1) 230 5 C
Immersion Time: (1) 2 0.5s
Immersion and emersion rates: 25mm/s
Flux: Ethanol solution of rosin, 25wt%
Pre-heat: 150 5 C, 60 5s
Solder: Sn/Pb = 60/40 or Sn-3.0Ag-0.5Cu solder
Solder Temperature: 270 5 C
Immersion Time: 10 1s
Immersion and emersion rates: 25mm/s
Initial values: About 220 to 22000pF, measured after Heat
treatment [150 C (
condition for 48 4 hrs.
Then measured after exposure to room conditions for
Following hours.
It should be soldered on the glass-epoxy substrate.
Applying Force (F): 17.6N
Applying Time: 60s
22 to 100pF: 1.0 0.1MHz
220 to 22000pF: 1.0 0.1kHz
22 to 100pF: 24 2 hrs.
220 to 22000pF: 48 4 hrs.
(2) Sn-3.0Ag-0.5Cu solder
Rdc 1
(2) 3 1s
0
10
(2) 240 3 C
C), 1 hour] and exposure in the room
Rdc 2
Test Methods
Test Methods
Continued on the following page.
Rdc 2
0.6
1.0
0.6
Rdc 1
C50E.pdf 05.1.28
0.6
(in mm)
1