BLM18BB331SH1D Murata, BLM18BB331SH1D Datasheet - Page 29
![EMI/RFI Suppressors & Ferrites 0603 330ohms HiSpeed Signal Line Tape](/photos/16/33/163388/lpmuratablm_sml.jpg)
BLM18BB331SH1D
Manufacturer Part Number
BLM18BB331SH1D
Description
EMI/RFI Suppressors & Ferrites 0603 330ohms HiSpeed Signal Line Tape
Manufacturer
Murata
Series
BLM Br
Datasheet
1.BLM18BD252SH1D.pdf
(46 pages)
Specifications of BLM18BB331SH1D
Shielding
Unshielded
Test Frequency
100 MHz
Product
Chip Ferrite Beads
Impedance
330 Ohms
Tolerance
25 %
Maximum Dc Current
200 mAmps
Maximum Dc Resistance
0.75 Ohms
Operating Temperature Range
- 55 C to + 125 C
Package / Case
0603 (1608 metric)
Termination Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
BLM18BB331SH1D
Manufacturer:
MURATA
Quantity:
240 000
3
!Note
!Note
Do not use products beyond the rated current and rated
voltage as this may create excessive heat and
deteriorate the insulation resistance.
Please provide special attention when mounting chip
"EMIFIL" (BLM_P) series in close proximity to other
products that radiate heat.
The heat generated by other products may deteriorate
the insulation resistance and cause excessive heat in
this component.
< Operating Environment >
Do not use products in a chemical atmosphere such as
chlorine gas, acid or sulfide gas.
< Storage and Handling requirements >
1. Storage Period
Noise suppression levels resulting from Murata's EMI
suppression filters "EMIFIL" may vary, depending on
the circuits and ICs used, type of noise, mounting
pattern, lead wire length, mounting location, and
other operating conditions. Be sure to check and
confirm in advance the noise suppression effect of
each filter, in actual circuits, etc. before applying
the filter in a commercial-purpose equipment design.
1. Washing
2. Soldering
Do not make any resin coating DLW31SH series.
Resin coating may cause a change in impedance value
or open circuit of wire.
28
!Caution/Notice
BLM series should be used within 6 months, the
other series should be used within 12 months.
Products to be used after this period should be
checked for solderability.
Failure and degradation of a product are caused by
the washing method. When you wash on the
conditions that are not in mounting information,
please contact Murata engineering.
Reliability decreases with improper soldering
methods. Please solder by the standard soldering
conditions shown in mounting information.
!Caution (Rating)
!Caution (Soldering and Mounting)
Notice (Storage and Operating Condition)
Notice (Rating)
Notice (Soldering and Mounting)
Notice (Handling)
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
2. Storage conditions
(1) Storage temperature : -10 to 40 degree C
(2) Do not store products in a chemical atmosphere
Relative humidity : 30 to 70%
Avoid sudden changes in temperature and humidity.
such as chlorine gas, acid or sulfide gas.
C50E.pdf 05.1.28