301-0-RC Xicon, 301-0-RC Datasheet - Page 2

• Manufacturer Part Number: 301-0-RC
• Description: Thick Film Resistors - SMD 1/16WATT 0OHMS
• Manufacturer: Xicon

Specifications of 301-0-RC

• Resistance: 0 Ohms
• Tolerance: 5 %
• Power Rating: 0.0625 Watt (1/16 Watt)
• Termination Style: SMD/SMT
• Package / Case: 0603 (1608 metric)
• Voltage Rating: 50 Volts
• Operating Temperature Range: - 55 C to + 125 C
• Dimensions: 0.8 mm W x 1.6 mm L x 0.45 mm H
• Product: Thick Film Resistors Zero-Ohm
• Temperature Coefficient: +/- 400 PPM / C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

5% Thick Film Chip Resistors (RoHS Compliant)
XC-600033
Characteristics
Temperature
coefficient
Short time
overload
Insulation
resistance
Dielectric
withstanding
voltage
Terminal bending
Temperature
cycling
Load life in
humidity
Load life
Soldering Heat
Solderability
CHARACTERISTICS
Specifications are subject to change without notice. No liability or warranty implied by this information. Environmental compliance based on producer documentation.
1Ω ~ 10Ω ≤ ±400 PPM / °C
11Ω ~ 10MΩ ≤ ±200 PPM / °C
Resistance change rate is
± (2.0 % + 0.1Ω) Max.
1,000M Ω or more
No evidence of flashover
mechanical damage,arcing or
insulation break down.
±(1.0% +0.05Ω) Max.
± (1.0% + 0.05Ω) Max.
Resistance change rate is
± (3.0% + 0.1Ω) Max.
Resistance change rate is
± (3.0% + 0.1Ω) Max.
Electrical characteristics shall be satisfied.
Without distinct deformation in
appearance.
95% Coverage min.
XICON PASSIVE COMPONENTS • [phone]
Limits
Test Methods ( JIS C 5201-1 )
5.2 Natural resistance change per temp.
degree centigrade.
R
R
R
R
5.5 Permanent resistance change after the
application of a potential of 2.5 times RCWV
for 5 seconds.
5.6 Apply 500V DC between protective coating
and termination for 1 minute
5.7 Apply 500V AC between protective coating
and termination for 1 minute
6.1.4 Twist of Test Board:
Y/X=5/90mm for 10 seconds
7.4 Resistance change after continuous
5 cycles for duty shown below:
7.9 Resistance change after 1,000 hours
(1.5 hours "on", 0.5 hour "off") at RCWV
in a humidity chamber controlled at
40°C ± 2°C and 90 to 95 % relative humidity
7.10 Permanent resistance change after 1,000 hours
operating at RCWV, with duty cycle of
( 1.5 hours "on", 0.5 hour "off" ) at 70°C ± 2°C ambient
Solder bath method
Reflow soldering method
Solder iron method
6.5 Test temperature of solder: 245° ±3°C
Dipping them solder: 2~3 seconds
2
1
1
2
-R
(t
: Resistance value at room temperature (t
: Resistance value at room temp.plus 100°C (t
2
1
-t
1
Step
)
1
2
3
4
Pre-Heat: 100 to 105°C, 30 ±5 sec.
Temperature: 265 ± 3°C, 5 +1/-0 sec
Peak: 250 +5/-0°C
230°C or higher, 30 ±10Sec.
Bit temperature: 350° ±10°C
Application time of soldering iron: 3 +1/-0 seconds
x10
6
(PPM/°C)
Temperature
+155°C ±2°C
Room temp.
Room temp.
-55°C ±3°C
CR5-RC Series
1
)
Date Revised: 9/30/05
2
)
10~15 mins
10~15 mins
30 mins
30 mins
Time