PV36W503C01B00 Murata, PV36W503C01B00 Datasheet - Page 9
![Trimmer Resistors - Multi Turn 50K 10%](/photos/16/50/165091/131p22_sml.jpg)
PV36W503C01B00
Manufacturer Part Number
PV36W503C01B00
Description
Trimmer Resistors - Multi Turn 50K 10%
Manufacturer
Murata
Specifications of PV36W503C01B00
Resistance
50 KOhms
Power Rating
0.5 Watt (1/2 Watt)
Operating Temperature Range
- 55 C to + 125 C
Element Type
Cermet
Product
Multi-Turn Trimmer Potentiometers
Termination Style
PCB
Tolerance
10 %
Number Of Turns
25
Taper
Linear
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PV36W503C01B00
Manufacturer:
MURATA
Quantity:
240 000
9
!Note
!Note
82
No.
10
Angle Sensing Potentiometer Specifications and Test Methods
1
2
3
4
5
6
7
8
9
Linearity
Temperature
Coefficient of
Resistance
Temperature
Cycle
(Thermal Shock)
Humidity
Vibration
Shock
Humidity Load
Life
High Temp.
Exposure
Low Temp.
Exposure
Rotational Life
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
Item
Independent linearity should vary no more than ±2% within ±160° to 50% voltage ratio.
Taper : linear, 100%/333.3° Measured with the circuit as below (Figure 1).
The rotary position sensor should be subjected to each of the following temperatures (see Table 1) for 30-45 minutes.
Temperature coefficient of resistance should be applied to the following formula.
TCR=
The rotary position sensor should be subjected to Table 2 temperature for 5 cycles.
Then, the rotary position sensor should be kept in the dry box for 24 +8/-0 hrs.
The rotary position sensor should be stored in a chamber at temperature of +60±2°C and relative Humidity of 90-95% for 250±8
hrs. After removing from the chamber, the rotary position sensor should be kept in the dry box for 24 +8/-0 hours.
The rotary position sensor should be tested under the condition of the amplitude of 1.5mm, the frequency range from 10 to 55Hz
(should be traversed in approximately one minute) and 2 hours in each of 3 mutually perpendicular directions (total 6 hours).
Then, the rotary position sensor should be kept in the dry box for 1-2 hrs.
The rotary position sensor should be tested under the condition of the peak acceleration 20G max. in half-sine wave and 5 shocks
in each of 3 mutually perpendicular directions (total 15 shocks). Then, the rotary position sensor should be kept in the dry box for
1-2 hrs.
Full rated continuous working voltage not exceeding 5Vdc should be applied intermittently between terminal #1 and terminal #3 of
the rotary position sensor, 1.5 hours on and 0.5 hours off, for 96±4 hours in total in a chamber at a temperature of +40±2°C and
relative humidity of 90-95%. After removing from the chamber, the rotary position sensor should be kept in the dry box for 24 +8/-
0 hours.
The rotary position sensor should be stored in a chamber at the temperature of +85±3°C without loading for 250±8 hours. After
removing from the chamber, the rotary position sensor should be kept in the dry box for 24 +8/-0 hours.
The rotary position sensor should be stored in a chamber at the temperature of -40±3°C without loading for 168±4 hours. After
removing from the chamber, the rotary position sensor should be kept in the dry box for 24 +8/-0 hours.
The adjustment rotor should be continuously rotated within ±160° of effective electrical rotational angle, at the rate of one cycle for
6 seconds for 1 Million cycles under the condition of +25±2°C of temperature without loading.
Note * : Reference temperature
Output voltage ratio (%)
Temperature (°C)
Temperature (°C)
V (1-2)
V (1-3)
R
t
t
R
R
Time (min.)
1
2
Sequence
Sequence
R
1
1
2
2
(t
: Reference temperature in degrees celsius
: Test temperature in degrees celsius
: Resistance at reference temperature in ohm
: Resistance at test temperature in ohm
– R
2
X100
– t
1
1
)
Z 10
100%
50%
0%
Table 2: One cycle of temperature cycle
6
(ppm/°C)
-160
Table-1 Test temperatures
-40±3
+25
30
*1
1
Guarantee limit for linearity
CCW
Rotational angle ( )
0
5 max.
+25±2
100% / 333.3
-40
2
2
CW
Test Methods
+160
+85±3
+25
30
*3
3
DC5V (#3)
5 max.
+25±2
+85
4
4
Figure-1
Connection Impedance : 1M ohm min.
GND (#1)
Output (#2)
R50E13.pdf 04.6.11