PVZ2A103C04R00 Murata, PVZ2A103C04R00 Datasheet - Page 27
![Trimmer Resistors - SMD 10Kohms Open 2mm Carbon](/photos/16/33/163349/poz2anpt_sml.jpg)
PVZ2A103C04R00
Manufacturer Part Number
PVZ2A103C04R00
Description
Trimmer Resistors - SMD 10Kohms Open 2mm Carbon
Manufacturer
Murata
Type
Trimming Potentiometerr
Datasheets
1.PVG5A101C01R00.pdf
(89 pages)
2.PVM4A201D01R00.pdf
(55 pages)
3.PVG5A201C01R00.pdf
(90 pages)
Specifications of PVZ2A103C04R00
Resistance
10 KOhms
Power Rating
0.1 Watt (1/10 Watt)
Operating Temperature Range
- 25 C to + 85 C
Element Type
Carbon
Dimensions
2.1 mm W x 2.7 mm L x 0.8 mm H
Product
Single-Turn Trimmer Potentiometers
Termination Style
Solder Pad
Tolerance
30 %
Number Of Turns
1
Taper
Linear
Temperature Coefficient
+/- 500 PPM / C
Product Type
Single Turn
Adjustment
Top Crossed
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PVZ2A103C04R00
Manufacturer:
MURATA
Quantity:
240 000
Part Number:
PVZ2A103C04R00
Manufacturer:
MURATA/村田
Quantity:
20 000
4
!Note
!Note
1. Store in temperatures of -10 to +40 deg. C and
2. Do not store in or near corrosive gases.
3. Use within six months after delivery.
4. Open the package just before using.
5. Do not store under direct sunlight.
6. If you use the trimmer potentiometer in an
1. When using with partial load (rheostat), minimize
2. The maximum input voltage to a trimmer
3. The maximum input current to a trimmer
1. Soldering
26
PVG3 Series Notice
(1) Standard soldering condition
(2) Cannot be soldered using the flow soldering
(3) The soldering iron should not come in contact
(4) Apply the appropriate amount of solder paste.
Notice (Operating and Storage Conditions)
relative humidity of 30-85%RH.
environment other than listed below, please
consult with a Murata factory representative prior
to using.
The trimmer potentiometer should not be used under
Notice (Rating)
the power depending on the resistance value.
potentiometer should not exceed (P.R)^1/2 or the
maximum operating voltage, whichever is smaller.
potentiometer should not exceed (P/R)^1/2 or the
allowable wiper current, whichever is smaller.
Notice (Soldering and Mounting)
(a) Reflow soldering :
(b) Soldering iron
Before using other soldering conditions more
than those listed above, please consult with a
Murata factory representative prior to using.
If the soldering conditions are not
suitable, e.g., excessive time and/or excessive
temperature, the trimmer potentiometer may
deviate from the specified characteristics.
method. If you use the flow soldering method,
the trimmer potentiometer may not function.
with the case of the trimmer potentiometer. If
such contact does occur, the trimmer
potentiometer may be damaged.
If the amount of solder paste applied to the
land is insufficient, the required adhesive
strength cannot be obtained. If an excessive
amount of solder paste is applied, solder
bridging or flux overflow to the resistive
element surface can occur.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
Temperature of tip : 400 deg. C max.
Soldering time
Diameter of tip
Wattage of iron
Refer to the standard temperature profile.
: 3 sec. max.
: 2mm dia. max.
: 30W max.
2. Mounting
3. Cleaning
(1) Corrosive gaseous atmosphere
(2) In liquid
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage nor electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
(1) Use our standard land dimension. Excessive land
(2) Do not apply excessive force (preferably 4.9N
(3) Do not warp and/or bend PC board to prevent
(4) In chip placers, the size of the cylindrical
(1) Isopropyl-alcohol and Ethyl-alcohol are
(2) Less than 3 minutes of total cleaning time by
(3) In case of ultra-sonic cleaning method, cleaning
the following environmental conditions:
(a) Power: 600W (67lit.) max.
(b) Frequency: 28kHz
(c) Temperature: Ambient temperature
(Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia
gas, Sulfuric acid gas, Nitric oxide gas, etc.)
(Ex. Oil, Medical liquid, Organic solvent, etc.)
area causes displacement due to the effect of the
surface tension of the solder. Insufficient
land area leads to insufficient soldering
strength of the chip.
(Ref.; 500gf) max.), when the trimmer
potentiometer is mounted to the PCB.
trimmer potentiometer from breakage.
pick-up nozzle should be outer dimension
2.5-3.0mm dia. and inner dimension
2.0-2.5mm dia..
applicable solvents for cleaning. If you use any
other types of solvents, please consult with a
Murata factory representative prior to using.
dipping, vapor and ultra-sonic method.
conditions should be as follows.
Due to ultra-sonic cleaning equipment's peculiar
self-resonance point and that cleaning
compatibility usually depends on the jig
Continued on the following page.
R50E13.pdf 04.6.11