1309G4 Anderson Power Products, 1309G4 Datasheet
1309G4
Manufacturer Part Number
1309G4
Description
Heavy Duty Power Connectors HAND TOOL FOR SB50 PP75 SBS50 CON
Manufacturer
Anderson Power Products
Series
SB50 Series, PP75 Seriesr
Specifications of 1309G4
Product Type
Tools
Standards
UL Listed and CSA Recognized
Tool Type
Crimp Tool
Wire Size
12-6 AWG
Crimp Size
12AWG To 8AWG
Crimp Tool
Hand Held Cycle-Controlled Crimp Tool
Rohs Compliant
NA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
Anderson Crimp Terminals
Tw o P o l e C o n n e c t o r s w i t h S i n g l e - p i e c e H o u s i n g s
• Insulated housing
• Silver plated contacts
ASSEMBLY INSTRUCTIONS
For installation by a qualified electrician in accordance with national and local
electrical codes
and the following instruction. The suitability of this type of termination must be
evaluated by
Underwriter's Laboratories, Inc. and Canadian Standard Association for the end use
application.
Assemble contact to the cables according to the equipment manufacturer's assembly
instructions.
The following instructions are supplied as a reference.
Please note:
Instructions are included with each crimp tool for terminating specific contacts. Use of
non-Anderson Power crimp can effect UL & CSA Approval.
1. Strip cable to dimensions in Table A.
2. *Crimp or solder contact to cable following Tables B, C and D.
3. Observing proper polarity, place contact in housing with notched side of tongue
next to spring.
4. Push contact and cable into housing until it snaps over end of spring; tug slightly to
make sure
* Soldering recommended for cables with solid or minimal conductor stranding
Table A:
Table B: Recommended Soldering Techniques
Recommended Soldering Techniques
Use rosin flux solder only. Wrap cable strands. Melt solder into well, heat and
insert stripped
cable. Continue heating well until solder flows into wire, being careful not to over
flow onto
contact surface. Do not solder-dip contacts. Cable clamps required for solder
connections
(required by Underwriter's Laboratories, Inc.) are listed on Table E (over).
(ex. THHN type wire).
(see cross section above).
contact is locked into place.
SBS™ Connector
Assembly Instructions
Cable Stripping Dimensions
Connector
Series
SBS™50
• Stainless steel springs
• Finger proof
"X"
inches
9/16
"X"
mm
14
Related parts for 1309G4
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
ANDERSON POWER PRODUCTS® 1367G1 PNEUMATIC CRIMP TOOL
Manufacturer:
Anderson Power Products
Part Number:
Description:
Manual Crimping Tool For Anderson Power Products Modular Power Connectors
Manufacturer:
Anderson Power Products
Part Number:
Description:
Manual Crimping Tool For Anderson Power Products Modular Power Connectors
Manufacturer:
Anderson Power Products
Part Number:
Description:
Heavy Duty Power Connectors ANDERSON 36/48V AR BCI PRO
Manufacturer:
Anderson Power Products
Part Number:
Description:
BUSHING, 6384G1 CONTACT
Manufacturer:
Anderson Power Products
Datasheet:
Part Number:
Description:
Quick Disconnect Terminal: 6.86: M: Silver Over Nickel
Manufacturer:
Anderson Power Products
Part Number:
Description:
PP15/45 2X2 HSG. BLK.BONDED
Manufacturer:
Anderson Power Products
1309G4 Summary of contents
Page 1
SBS™ Connector Assembly Instructions ...
Page 2
... Connector Wire Sizes Wire Sizes Tool Rating AWG 50 amps #16-6 50 amps #16-4/0 AWG Wire Size #6-8 #6-10 & 12 #6-14 & 16 For One Twin Conductor Cables 5905 931, 658; 1,295,598. Anderson Power Products ® www.andersonpower.com mm Part Number 1.5-16.0 1309G4 1.5-107.0 1387G1 1S6417 Rev03 ...