142-0307-011 Emerson Network Power, 142-0307-011 Datasheet - Page 10

• Manufacturer Part Number: 142-0307-011
• Description: RF Connectors STRT AU FEM ST CRIMP JACK
• Manufacturer: Emerson Network Power
• Type: Cable Jackr

Specifications of 142-0307-011

• Body Style: Straight
• Cable Type: RG58, RG141, RG303
• Connector Type: Jack Crimp
• Frequency Range: 0 GHz to 12.4 GHz
• Rf Series: SMA
• Product: Various Connectors
• Gender: Female
• Shell Plating: Gold
• Impedance: 50 Ohms
• Maximum Frequency: 12.4 GHz
• Angle: Straight
• Contact Plating: Gold
• Finish, Housing: Gold
• Material, Contact: Beryllium Copper
• Material, Dielectric: TFE
• Material, Housing: Brass
• Primary Type: SMA
• Special Features: 3-Pc, Captivated Contact
• Termination: Crimp
• Voltage, Rating: 335 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Assembly
Instructions
1. Identify connector parts. (3 piece parts - except bulkhead)
2. Strip cable to dimensions shown. Do not nick braid or center conduc-
3. Assemble contact onto cable as shown.
4. Flare braid and slide body assembly over contact and under braid.
10
SMA TYPE STRAIGHT PLUGS,
STRAIGHT JACKS, AND STRAIGHT
BULKHEAD JACKS FOR FLEXIBLE CABLE -
CRIMP OR SOLDER CONTACTS
tor. Tin center conductor if contact will be solder attached. Do not tin
center conductor if contact is to be crimp attached. When stripping
LMR-100 low loss cable, remove foil back to where cable jacket is
stripped. A wire stripper of correct size is recommended for this step.
Slide heat shrink (as applicable) and crimp sleeve onto jacket of cable.
Solder Attachment: Solder contact to center conductor through sol-
der hole using .020 (0.51) diameter solder. Use a minimum amount
of solder for a good joint.
Crimp Attachment: Crimp contact to center conductor using JCI
Hand Tool 144-0000-910, setting #2, with positioner 141-0000-907.
Crimp location should be centered between end of contact and X-
hole. Crimp attachment to solid center conductor cables is not rec-
ommended.
Then seat body assembly firmly onto contact. The cable may have to
be held in a clamping fixture. Arrange braid uniformly around crimp
stem. Slide crimp sleeve forward and crimp using recommended crimp
tool. Slide heat shrink forward and shrink (as applicable).
Johnson Components
®
• P.O. Box 1732 • Waseca, MN 56093-0832 • 1-800-247-8256 • Fax: [phone] • www.johnsoncomp.com
RG 316/u, 161, 174, 188; LMR-100
RG 316/u, 161, 174, 188; LMR-100
RG 316/u, 161, 174, 188; LMR-100
RG 316/u, 161, 174, 188; LMR-100
RG 316/u, 161, 174, 188; LMR-100
RG 316/u, 161, 174, 188; LMR-100
RG 55/u, 142, 223, 400
RG 55/u, 142, 223, 400
RG 55/u, 142, 223, 400
RG 55/u, 142, 223, 400
RG 55/u, 142, 223, 400
174, 188; LMR-100
RG 316DS, 188DS
RG 316DS, 188DS
RG 316DS, 188DS
RG 316DS, 188DS
RG 316DS, 188DS
RG 316DS, 188DS
RG 58/u, 141, 303
RG 58/u, 141, 303
RG 58/u, 141, 303
RG 58/u, 141, 303
RG 58/u, 141, 303
CABLE GROUP
RG 316/u, 161,
RG 179/u, 187
RG 55/u, 142,
RG 316DS,
RG 179/u,
RG 58/u,
141, 303
223, 400
188DS
187
CUSTOMER DRAWINGS AVAILABLE UPON REQUEST
142-0303-011/016
142-0303-411/416
142-0304-011/016
142-0307-011/016
142-0307-411/416
142-0308-011/016
142-0308-411/416
142-0333-011/016
142-0403-011/016
142-0404-011/016
142-0407-011/016
142-0408-011/016
142-0433-011/016
142-2403-001/006
142-2404-001/006
142-4303-401/406
142-4304-401/406
142-4307-401/406
142-4308-401/406
142-4403-001/006
142-4404-001/006
142-4407-001/006
142-4408-001/006
142-5303-401/406
142-5304-401/406
142-5307-401/406
142-5308-401/406
142-5403-001/006
142-5404-001/006
142-5407-001/006
142-5408-001/006
142-0304-411/416
142-0333-411/416
PART NUMBER
INCHES (MILLIMETERS)
CRIMP HEX
.128 (3.25)
.151 (3.83)
.128 (3.25)
.151 (3.83)
.213 (5.41)
.128 (3.25)
.151 (3.83)
.213 (5.41)
.128 (3.25)
.151 (3.83)
.213 (5.41)
.128 (3.25)
.151 (3.83)
.213 (5.41)
.128 (3.25)
.128 (3.25)
.151 (3.83)
.151 (3.83)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.128 (3.25)
.128 (3.25)
.128 (3.25)
.151 (3.83)
.213 (5.41)
.213 (5.41)
.128 (3.25)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.213 (5.41)