ABA.00.250.NTL LEMO, ABA.00.250.NTL Datasheet - Page 44

• Manufacturer Part Number: ABA.00.250.NTL
• Description: RF Connectors ADAPTOR SOCKET TO BNC PLUG
• Manufacturer: LEMO

Specifications of ABA.00.250.NTL

• Body Style: Adapter
• Connector Type: Adapter
• Features: IP rating 50
• Housing Material: Brass
• Length: 28.5 mm
• Mounting Angle: Straight
• Operating Temperature Range: - 55 C to + 260 C
• Rf Series: Between Series
• Product: Adapters
• Gender: Male, Female
• Polarity: Normal
• Shell Plating: Nickel
• Impedance: 50 Ohms
• Termination Style: Quick Connect
• Convert From: LEMO Socket
• Convert To: BNC Plug
• Side 1 Rf Series: Lemo 00
• Side 2 Rf Series: BNC
• Side 2 Gender: Plug (Male)
• Adapter Style: Straight
• Body Material: Brass
• Side 1 Gender: Plug (Male)
• Side 1 Polarity: Normal
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Terminating of elbow plugs (90°) with cable collet (solder contact)
42
®
L ± 0.2
Solder
T ± 0.2
S ± 0.2
®
1
2
3
1.
2.
2.1 Place the crimp ferrule ➀ and
2.2 Slide the assembly into
2.3 Place the insulating sleeve ➃
2.4 Close the access hole with
Note: these terminating instruc-
tions apply to the following
models:
M6 = FLA
1-2-3-4-8
4
Cable
group
Cable preparation
First place the bend relief
(if to be used) on the cable.
Strip the cable according to
dimensions below.
Cable terminating
collet ➁ on the cable. Fold
back the shield braid onto
the conical part of the collet,
and trim to outer edge of the
collet.
the connector shell ➂
and tighten the collet nut ➀
using the appropriate tool
to a torque of 0.25 Nm
(see “Tooling” on page 35,
36 and 37). Check that
the cable conductor rests
in the contact slot, solder
the conductor through
the hole.
over the soldered contact.
the flat screw ➄.
Push the bend relief (if used)
onto the collet nut ➀.
5
T
1
M6
3.5
S
6.5
L
Solder
L
T
0.2
M6
S
0.2
0.2
and cable crimp (solder contact)
1
2
1.
2.
2.1 Place the cable crimp ferrule
2.2 Slide the cable into the con-
2.3 Place the insulating sleeve ➂
2.4 Close the connector hole
Note: these terminating instruc-
tions apply to the following
models:
M7 = FLS, FLV
1-2-3-4-8
3
Cable
group
Cable preparation
First place the bend relief
(if to be used) on the cable.
Strip the cable according to
dimensions below.
Cable terminating
➀ on the cable and widen
the braiding.
nector shell ➁. Check that
cable conductor rests in the
contact slot, tin solder the
conductor through the hole.
Slide the crimp ferrule ➀ over
the braiding until it reaches
the connector shell ➁. Crimp
with the LEMO crimp tool
using the hexagonal opening
(see “Tooling” on page 37).
over the soldered contact.
with the flat screw ➃.
Push the bend relief (if used)
onto the crimping tube ➀.
6-7
4
T
1
3
www.lemo.com
M7
4.5
4.5
S
M7
11
L
9