G5V-2-H1-DC5 Omron, G5V-2-H1-DC5 Datasheet - Page 4

• Manufacturer Part Number: G5V-2-H1-DC5
• Description: Low Signal Relays - PCB DPDT PCB 5VDC
• Manufacturer: Omron
• Series: G5V2r

Specifications of G5V-2-H1-DC5

• Contact Form: 2 Form C
• Coil Voltage: 5 VDC
• Coil Current: 72 mA
• Coil Type: Non-Latching
• Power Consumption: 150 mW
• Termination Style: Solder Pin
• Maximum Switching Current: 2 A
• Contact Rating: 0.50 A at 125 VAC, 2 A at 30 VDC
• Current, Rating: 0.5⁄1 AAC⁄ADC
• Diameter, Mounting: 0.039 in. Dia. (Hole)
• Dielectric Rating: 1000 VAC @ 50⁄60 Hz for 1 minute between coil and contacts
• Dimensions: 0.807 in. L x 0.398 in. W x 0.453 in. H
• Function: Sensitive
• Material, Contact: Ag (Au clad)
• Number Of Pins: 8
• Power, Rating: 62.5⁄24 VA⁄W
• Relay Type: Electro Mechanical
• Standards: UL, CSA, FCC, RoHS
• Temperature, Operating, Maximum: 70 °C
• Temperature, Operating, Minimum: -25 °C
• Voltage, Control: 5 VDC
• Voltage, Rating: 125 VAC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: G5V2H15DC OMRG5V2H15DC

Dimensions
Note: 1. All units are in millimeters unless otherwise indicated.
G5V-2, G5V-2-H1
■ Approvals
UL Recognized (File No. E41515) / CSA Certified (File No. LR31928) - - Ambient Temp. = 40°C
Note: 1. The rated values approved by each of the safety standards may be different from the performance characteristics individually defined in this catalog.
Precautions
Long-term Continuously ON Contacts
Using the Relay in a circuit where the Relay will be ON continuously
for long periods (without switching) can lead to unstable contacts
because the heat generated by the coil itself will affect the insulation,
causing a film to develop on the contact surfaces. Be sure to use a
fail-safe circuit design that provides protection against contact failure
or coil burnout.
80
G5V-2
G5V-2-H1
2. Tolerance: ±0.1
3. Orientation marks are indicated as follows:
2. In the interest of product improvement, specifications are subject to change.
Type
Low Signal Relay
DPDT
0.5
20.5 max.
20.3 typ.
Contact form
G5V-2
0.3
3 to 48 VDC
3 to 48 VDC
10.1 max.
9.9 typ.
7.62
Coil rating
3.5
0.5
11.5 max.
11.4 typ.
Terminal Arrangement/
Internal Connections
(Bottom View)
Relay Handling
When washing the product after soldering the Relay to a PCB, use a
water-based solvent or alcohol-based solvent, and keep the solvent
temperature to less than 40°C. Do not put the Relay in a cold clean-
ing bath immediately after soldering.
16
1
0.6 A at 125 VAC (General Use)
0.6 A at 110 VDC (Resistive)
2 A at 30 VDC (Resistive)
0.5 A at 125 VAC (General Use)
0.2 A at 110 VDC (Resistive)
1 A at 24 VDC (Resistive)
13
4
11
6
9
8
(1.3)
Eight, 1-dia. holes
Contact ratings
7.62
Tolerance: ±0.1
Mounting Holes
(Bottom View)
5.08 5.08
7.62
(1.3)
(1.2)