RSP-1500-12 Mean Well, RSP-1500-12 Datasheet - Page 4
![Linear & Switching Power Supplies 12V 125A 1500W Active PFC Function](/photos/17/98/179860/rsp1500_sml.jpg)
RSP-1500-12
Manufacturer Part Number
RSP-1500-12
Description
Linear & Switching Power Supplies 12V 125A 1500W Active PFC Function
Manufacturer
Mean Well
Series
RSP-1500r
Datasheet
1.RSP-1500-12.pdf
(4 pages)
Specifications of RSP-1500-12
Product
Switching
Output Power Rating
1500 W
Input Voltage
127 VDC to 370 VDC
Number Of Outputs
1
Output Voltage (channel 1)
12 V
Output Current (channel 1)
125 A
Dimensions
278 mm L x 127 mm W x 83.5 mm H
Open Frame/enclosed
Enclosed
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
2.Alarm Signal Output
3.Output Voltage TRIM
4.Current Sharing
(1)Alarm signal is sent out through "P OK" & "P OK GND" pins
(2)An external voltage source is required for this function. The maximum applied voltage
(3)Table 2.1 explain the alarm function built-in the power supply
(1)Adjustment of output voltage is possible between 70~100%(Typ.) of the rated output which is shown in Fig. 3.1
(2)Connecting a resistor externally between TRIM and-S on CN1 or CN2 that is shown in Fig. 3.2.
(1)Parallel operation is available by connecting the units shown as below
(2)The voltage difference among each output should be minimized that less than 2% is required
(3)The total output current must not exceed the value determined by the following equation
(4) In parallel operation 4 units is the maximum, please consult the manufacture for other
(5) When remote sensing is used in parallel operation, the sensing wire must be connected only
Function
(+S,-S and LS are connected mutually in parallel):
P OK
is 50V and the maximum sink current is 10mA
(Output current at parallel operation)=(The rated current per unit) x (Number of unit) x 0.9
applications
to the master unit
The signal is "Low" when the power supply is
65% of the rated output voltage-Power OK
The signal turns to be "High" when the power supply
is under 65% of the rated output voltage-Power Fail
100%
1500W Single Output Power Supply
90%
80%
70%
Vout
Fig. 3.1 External Resistor (Typical)
0
Description
470
Table 2.1 Explanation of alarm
1.8K
OPEN
above
Low
(0.5V max at 10mA)
High or open
(External applied voltage
10mA max.)
Output of alarm(P OK)
R
No.1(Master)
No.2(Slave)
No.3(Slave)
No.4(Slave)
AC/L AC/N
AC/L AC/N
AC/L AC/N
AC/L
Fig. 2.2 Internal circuit of P OK (Open collector method)
AC/N
Fig. 3.2 Output voltage trimming
R S P - 1 5 0 0
CN1
CN2
or
0.1uF
P OK
P OK GND
TRIM
-S
+S
-S
LS
+S
-S
LS
+S
-S
LS
+S
-S
LS
+S
-S
LS
+S
-S
LS
+S
-S
LS
+S
-S
LS
CN1
CN2
CN1
CN2
CN1
CN2
CN1
CN2
V-
V-
V-
V-
100K
File Name:RSP-1500-SPEC 2010-10-18
V+
V+
V+
V+
External voltage and R
(The max. Sink is 10mA and 50V)
R(0.5W)
R
+S
-S
s e r i e s
V
+V
-V
Load