DMS-30DR-3-R-C Murata Power Solutions Inc, DMS-30DR-3-R-C Datasheet - Page 2
![Digital Panel Meters 3.5 Digit LED 200V Daylight Readable](/photos/18/5/180586/dms30dr_sml.jpg)
DMS-30DR-3-R-C
Manufacturer Part Number
DMS-30DR-3-R-C
Description
Digital Panel Meters 3.5 Digit LED 200V Daylight Readable
Manufacturer
Murata Power Solutions Inc
Type
Panel Metersr
Datasheet
1.DMS-30DR-1-R-C.pdf
(6 pages)
Specifications of DMS-30DR-3-R-C
Equipment Type
Panel Meters
Display Type
3 - 1/2 Digit LED
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Performance/Functional Specifi cations
Typical at T
unless otherwise noted.
➀ Applies for transient or continuous overvoltages applied to (+) INPUT HI (pin 11) with
➁ See Technical Notes.
Analog Inputs
Full Scale Input Range:
Input Impedance:
Overvoltage Protection ➀
Common Mode Voltage Range
CMRR (dc to 60Hz)
Control Inputs ➁
Decimal Point Placement (Pins 4-6)
Ext. Bright (Pin 2)
Performance
Sampling Rate
Accuracy (3 minute warm-up):
Zero Reading (Vin = 0 Volts)
Temperature Drift (0 = +60°C)
+1.225V Reference Output (Pin 9)➁
Power Supply Requirements
Supply Voltage
Supply Current:
Display
Display Type and Size
Polarity Indication
Overrange Indication
Physical/Environmental
Operating Temperature
Storage Temperature
Humidity (non-condensing)
Case Material
Weight
Total Darkness
DMS-30DR-0
DMS-30DR-1
DMS-30DR-2
DMS-30DR-3
DMS-30DR-0, -1
DMS-30DR-2, -3
DMS-30PC-0 (Vin = +0.19V)
DMS-30PC-1 (Vin = +1.9V)
DMS-30PC-2 (Vin = +19V)
DMS-30PC-3 (Vin = +190V)
Full Sunlight
(–) INPUT LO (pin 12) properly connected. Pin 12 is not overvoltage protected
(see Figure 1). Voltages applied to pin 12 should not exceed the supply voltage.
A
= +25°C and supply voltage = +5V using the single-ended input circuit,
+1.215
“–001”
Min.
Tie to pin 3 to activate
See Technical Note 1
+4.75
100
–40
0.9
–
–
–
–
–
–
–
–
–
–
–
–
–
0
0
3½ digit, 0.56"/14.2mm high LED
Autopolarity ("–" for negative Vin)
–
–
"–1_ _ _ " for negative inputs
"1_ _ _ " for positive inputs
0.75 ounces (21 grams)
2.5 reading per second
+1.225
+5.00
+150
Typ.
±200
±200
1000
“000”
±0.2
±20
Polycarbonate
±2
86
±1
±1
±2
±2
1
–
–
–
–
–
3
+1.235
+5.25
+250
Max.
±250
“001”
±0.4
+60
+75
±2
±3
±3
±3
±3
95
–
–
–
–
–
–
–
5
www.murata-ps.com/dpm
Volts
Cnts/°C
Units
Counts
Counts
Counts
Counts
Volts
Volts
Volts
Volts
Volts
Volts
MΩ
MΩ
mA
mA
mV
dB
°C
°C
%
TECHNICAL NOTES
DMS-30DR- 1 - R - C
1. External Brightness Adjustment (Pin 2): Pin 2 is internally con-
2. Minimum-Intensity Adjustment Potentiometer: Users can adjust
3. +1.225V REFERENCE OUTPUT (Pin 9): This pin is the output of the
Ordering Information
Accessories:
Input Range:
nected to the high impedance input of an operational amplifi er that
amplifi es the output of the DMS-30DR’s ambient light sensor (ALS)
circuit. The output of this amplifi er varies the voltage that drives the
DMS-30DR’s LED display. Leave pin 2 open for standard auto-dim-
ming operation; in this mode, the ALS circuit will automatically adjust
the DMS-30DR’s LED brightness to compensate for changes in ambi-
ent lighting. As the ambient light striking the ALS increases, the LED
display’s brightness will also increase; a decrease in ambient light will
reduce the display’s brightness.
The ALS circuit’s output signal can be overdriven by applying an
externally generated voltage directly to pin 2. External drivers will see
approximately 600Kohms referenced to 5V RETURN. With pin 2 at
+0.7Vdc or below, the DMS-30DR’s LED display is off, and total cur-
rent drain from a nominal +5V supply is approximately 1mA. The LED
display’s brightness will increase from minimum to maximum as the
voltage applied to pin 2 is varied from +0.8V up to +2.5V, respectively.
To enable continuous maximum display brightness, connect pin 2
directly to pin 1 (+5V SUPPLY); in this confi guration the total current
drain for the meter will be approximately 200mA.
the DMS-30DR’s minimum LED brightness to suit their requirements
by adjusting the ¾-turn, rear-mounted intensity adjustment poten-
tiometer. Please note, this potentiometer will have minimal impact
on display brightness in high ambient light environments. See the
Mechanical Specifi cations section for potentiometer locations.
The intensity adjustment potentiometer is factory preset to its
mid-point position, producing a typical current drain of 7mA. At it’s
minimum and maximum positions, current drain is typically 3mA and
13mA, respectively. As viewed from the rear of the meter, with the
model number label facing up, turning the potentiometer clockwise
increases the display’s intensity.
meter’s precision +1.225V internal reference IC. Pin 9 is referenced
to ANALOG COMMON (pin 10), which in turn sits approximately +2V
above pin 3. Pin 9 should be buffered if it’s used to drive external
loads since sourcing more than 15μA of current can affect both the
A panel-mount DMS-BZL2-C is supplied with each unit.
DMS-EB-C
DMS-EB-RMS-C
DMS-30-CP
0 = ±200mV
1 = ±2V
2 = ±20V
3 = ±200V
Sunlight Readable, 3½ Digit Panel Meters
Multi-purpose (gain/offset, 4-20mA, etc.)
For true rms measurements of ac voltages
Panel cutout punch
DMS-30DR Series
LED Color:
03 Aug 2010 MPM_DMS-30DR.B05 Page 2 of 6
R = Red
with Auto-Dimming LED Displays
RoHS Compliant
email: sales@murata-ps.com