2102-P Techspray, 2102-P Datasheet - Page 6

• Manufacturer Part Number: 2102-P
• Description: Chemicals CONFORMAL COAT SR
• Manufacturer: Techspray
• Type: Conformalr

Specifications of 2102-P

• Product: Coating Products
• Size: 1 pint
• Container: Glass
• Chemical Component: 2-Butanone/Acetone/Dimethylmethylphenylmethoxysiloxane/Hexane Isomers Dipropylene Glycol Methyl Ether Acetate/Methyltrimethylsilane/Propane/Silicone Polymer/Toluene
• Dielectric Constant: 2.33
• Dielectric Strength: 1100 Dry
• Dispensing Method: Bottle
• Elongation: 60% @ 25 °C
• Primary Type: Coating
• Specific Gravity: 1.11 @ 25 °C
• Temperature Range: -65 to +200 °C
• Temperature, Rating: -65 to +200 °C
• Tensile Strength: 600 PSI @ 25 °C
• Thermal Conductivity: 0.17 W⁄mK @ 100 °C
• Time, Curve: 72 hr
• Time, Setting: 1 hr.
• Viscosity: 4 to 10⁄60 to 90 cps
• Volume Resistivity: 1 x 10^14 Dry
• Weight: 1 Pint
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

9. PHYSICAL AND CHEMICAL PROPERTIES
10. STABILITY AND REACTIVITY
1-(2-Methoxy-Methyl-Ethoxy)-2-Propanol Acetate
Polysiloxane mixture
Benzene- methyl, (Toluene)
Fine-L-Kote™ SR
ENGINEERING CONTROLS: Local exhaust ventilation may be necessary to control any air contaminants to
within their TLVs during the use of this product.
PERSONAL PROTECTIVE EQUIPMENT
PHYSICAL STATE: Liquid
pH: Not Applicable
PERCENT VOLATILE: 86 at 20°C (68°F)
BOILING POINT: 79°C (134°F)
SOLUBILITY IN WATER: Insoluble
SPECIFIC GRAVITY: 0.83 (water=1)
(VOC): 481 g/L (non-exempt VOC)
STABLE: YES
HAZARDOUS POLYMERIZATION: NO
CONDITIONS TO AVOID: Heat, flames, ignition sources, and incompatables.
STABILITY: Stable.
INCOMPATIBLE MATERIALS: Concentrated nitric and sulfuric acid mixtures, chloroform, alkalis, chlorine
compounds, acids, potassium t-butoxide.
OSHA TABLE COMMENTS:
1. NL = Not Listed
2. S = Skin
3. C = Ceiling
EYES AND FACE: For normal conditions, wear safety glasses. Where there is reasonable probability of liquid
contact, wear splash-proof goggles.
SKIN: The glove(s) listed below may provide protection against permeation. Gloves of other chemically
resistant materials may not provide adequate protection. Viton, Solvex, Butyl, Buna, Neoprene.
RESPIRATORY: A respiratory protection program that meets OSHA 1910.134 and ANSI Z88.2 requirements
must be followed whenever workplace conditions warrant a respirator's use.
STEL
TWA
STEL
NL
ppm
200
ppm
C300
ppm
[3]
NL mg/
m3
375 mg/
m3
560 mg/
m3
NL
ppm
S 50
ppm
NL
ppm
[2]
NL mg/
m3
188 mg/
m3
NL mg/
m3
NL
ppm
NL
NL
NL mg/
m3
NL
NL