467MP-3"x60yd 3M, 467MP-3"x60yd Datasheet - Page 4

• Manufacturer Part Number: 467MP-3"x60yd
• Description: Tapes & Mastics ADH TRANSFER TAPE TAN 58# 3 X 60YD
• Manufacturer: 3M

Specifications of 467MP-3"x60yd

• Product: Tape
• Size: 3 in x 60 yds
• Description/function: High Performance Adhesive Transfer Tape
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 2120019334

3M
467MP • 468MP • 467MPF • 468MPF • 7952MP • 7955MP
7962MP • 7965MP • 9172MP • 9185MP • 9667MP • 9668MP
Typical Physical
Properties and
Performance
Characteristics
(continued)
™
High Performance Adhesive Transfer Tapes with Adhesive 200MP
Note: The following technical information and data should be considered representative
III. Relative High Temperature Operating Ranges
Short term (minutes/hours)
Long term (days/weeks)
IV. Static Shear
ASTM D3654 - 1" x 1" sample area - aluminum foil to stainless steel
Temperature
70°F (21°C)
200°F (93°C)
350°F (177°C)
450°F (232°C)
450°F (232°C)
V. Shelf Life of Tape in Roll Form
VI. Adhesion Retention after Immersion and Exposure (percent retention)
Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm
Control adhesion value in ounces/inch
gasoline - 1 hour RT immersion
MEK - 1 hour RT immersion
weak acid - 4 hour RT immersion
weak base - 4 hour RT immersion
oil (10W30) - 72 hour, 120°F (49°C) immersion
water - 100 hours, 70°F (21°C)
salt water (5%) - 72 hours, 70°F (21°C)
warm/humid - 7 days, 90°F (32°C) and 90% relative humidity
UV cabinet - 30 days, 70°F (21°C)
Temperature Cycle - *Three cycles
VII. Low Service Temperature
*One cycle is 4 hours, 158°F (70°C); 4 hours, -20°F (-29°C); 16 hours, 70°F (21°C)
The glass transition temperature for 3M adhesive 200MP is -31°F (-35°C). Many
applications survive below this temperature (factors affecting successful applications include:
materials being bonded, dwell at RT before cold exposure and stress below the TG [i.e.
expansion/ contraction stresses, impact]). Optimum conditions are: bonding high surface
energy materials, longer time at RT before cold exposure and little or no stress below the Tg.
6
Adhesive 200MP is not recommended for low energy plastics (polypropylene,
polyethylene, powder coated paints). For these surfaces please refer to 3M™ Adhesives
300, 350, 300LSE and 300MP. The 3M™ Adhesive 300LSE has been used more
frequently as the bond areas in applications become smaller. It offers the smooth, high
performance characteristics of the 3M adhesive 200MP with higher adhesion to plastic.
3M adhesive 300LSE is ideal for polyethylene, polypropylene, powder coated paints and
for applications where the bonded area to plastic is less than 1/2" wide.
or typical only and should not be used for specification purposes.
2000 grams
1000 grams
500 grams
400 grams
200 grams
- 4 -
Load
400°F (204°C)
300°F (149°C)
24 months from the manufacturing date when
stored at 70°F (21°C) and 50% relative humidity.
10,000+
10,000+
10,000+
10,000+
2 mil
60
Minutes to Failure
101 oz./inch
3M™ Adhesive 200MP
146%
105%
105%
131%
147%
148%
2 mil
89%
64%
86%
84%
10,000+
10,000+
10,000+
10,000+
5 mil
149 oz./inch
75
158%
141%
116%
101%
5 mil
83%
66%
86%
83%
93%
93%