FH 0300 091 Amphenol, FH 0300 091 Datasheet - Page 46
![Crimping, Stripping, Cutting Tools & Drills spanner wrench](/photos/18/16/181600/abb_c091d_zub2_sml.jpg)
FH 0300 091
Manufacturer Part Number
FH 0300 091
Description
Crimping, Stripping, Cutting Tools & Drills spanner wrench
Manufacturer
Amphenol
Type
Spanner Wrenchr
Datasheet
1.FH_0300_091.pdf
(52 pages)
Specifications of FH 0300 091
Product
Tool Component
Description/function
For C-091
Svhc
No SVHC (15-Dec-2010)
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
81K2008
46
C 091
Remarks
Safety classification
1. General Remarks
These connectors are designed and produced in conformity with the low voltage directive (73/23/EWG) respectively Gerätesicherheitsgesetz (German law)
and are especially in accordance with the standards DIN EN 61984 (VDE 0627); IEC 60664-1 (VDE 0110-1) and IEC 60529.
The connectors may be used only within the technical ratings.
All technical data refer to mated connectors under live conditions. The safety of the connector system depends on the correct selection of products, proper
assembly of the connector device, and a precise fit of the connectors.
2. Application Remarks
Connectors with / without breaking capacity must be used according to specified technical ratings.
The technical data represent the initial value of mated parts under predetermined conditions and length of time.These values could change with different
test parameters or product requirements.
The C 091 Series connectors are used in a wide variety of industries and equipment. Some of these include industrial machines and controls, data
processing, instrumentation and test equipment, medical devices, telecommunication’s network and equipment, plus outdoor and marine applications.
All rated data for the connectors listed in this catalog are based on over-voltage category and pollution degree for electronic applications. Connectors were
completely mated according to their respective safety locking mechanism. Selection and testing of connectors with / without breaking capacity to
meet specific product or industrial requirements such as rated voltage and the related clearances and creepage distances are the responsibility of the user.
3. Assembling Remarks
Certain appliances and equipment include protective measures that relate to the coupling devices of the male and female receptacle housings.
(see also DIN VDE 0100 part 410; IEC 60364-4-41).
Care must be taken to insure the parts are correctly mated and screws are tightened with the proper torque. Protection against electrical shock on the
termination side of the connector (receptacles, contact insert) shall be secured by suitable mounting.
4. Termination Remarks
The dimensions as stated in the assembly instructions are for general information only and can vary depending on cable styles and types.
Please note in the case of an internal strain relief: Always clamp the outer cable mantle (not the individual lead wires) to avoid damage of the lead wire
insulation. In case of shielded cables, fold the braid over the outer mantle to avoid damage of the lead wire insulation when clamping the braid.
In case of clamping rings, make sure that the lead wire insulation is not damaged when connecting (clamping) the braid.
Cable connectors are effectively secured when using the internal cable clamp. When the connector contains a simple gland bushing for retention the cable
should have a strain relief close behind the connector. All cable properties or specifications must be compatible with the connector design and materials.
Designated wire conductors must be terminated to the correct poles in the connector.
Crimp contacts must be fully inserted into the plastic housing and retention assured with a slight tug on the wire.
Wire should be stripped correctly according to printed specifications to ensure no electrical contact can be made between the conductors. There should be
no nicked or cut strains during the stripping action.
5. Classification according to DIN EN 61984 / IEC 61984 (VDE 0627)
1)
Style
Male cable connector
Female cable connector
Male panel connector
Female panel connector
Protection against electrical shock on the termination side has to be secured by proper mounting.
X
X
X
X
X
X
X
X
X
1)
1)
X
X
1)
X
X
1)
X
X
X
X
X
X
with
Cable clamp
without
X
X
Amphenol