159-32821 Kobiconn, 159-32821 Datasheet

159-32821

Manufacturer Part Number

159-32821

Description

Crimping, Stripping, Cutting Tools & Drills DIE SET INSUL. 26-14

Manufacturer

Kobiconn

Type

Crimp Tool Assemblyr

Datasheet

1.159-32821.pdf (2 pages)

Specifications of 159-32821

Product

Crimping, Stripping & Cutting Tools & Drills

Description/function

Hand crimp tool assembly

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

Current page: 1 of 2
Download datasheet (199Kb)

Date Last Revised: 10/10/08

Speciﬁcations are subject to change without notice. No liability or warranty implied by this information. Environmental compliance based on producer documentation.

INTRODUCTION.

This instruction sheet provides application and maintenance procedures for the Hand Crimping Tool. (See Figure 1.) This tool is

designed to acept interchangeable crimping die assemblies. Read these instructions thoroughly before installing dies and using the

tool.

2. DESCRIPTION.

The Hand Crimping Tool consists of two crimping jaws, an adjustable ratchet, spring-actuated handles, two die retaining screws, and

an emergency ratchet release. The slotted design of the crimping jaws permits easy installation and removal of crimping dies. The

adjustable ratchet allows handle pressure to be set for optimum crimping die performance.

3. DIE INSTALLATION AND REMOVAL.

Select the desired die assembly, remove the die retention screws from the tool jaws, and proceed as follows:

3.1 Shouldered Dies (Figure 2)

1. Place the upper die in the stationary jaw of the tool frame.

2. Insert a die retention screw through the jaw and die and tighten the screw so that the die is held in place, but do not tighten the

3. Place the lower die in the moving jaw of the tool frame. Install a die retention screw through the jaw and die and tighten the screw

4. Slowly close the tool handles, allowing the dies to mate and/or align. Continue closing the tool handles until the ratchet makes the

5. To remove the die assembly, close the tool handles until the ratchet releases, and allow the handles to open fully. Loosen and

3.2 Pinned Dies (Figure 3).

1. Install wire and insulation anvil dies, with the chamfers facing the front of the tool, and with the die markings facing outward, into the

2. Insert the die retaining pins and the short die retention screw. Do not tighten the screw completely.

3. Install the wire and insulation crimper dies, with the chamfers facing the front of the tool, and with the die markings facing outward,

4. Insert the die retaining pins the long die retention screw. Do not tighten the screw completely.

5. Slowly close the tool handles, allowing the dies to mate and/or align. Continue closing the tool handles until the ratchet makes the

6. Install the locator assembly and tighten the hex nut.

7. Reverse the procedure to remove the die assembly.

screw completely at this point. Note: Die assembies with center contact crimp sections should be installed with the center contact

crimp section toward the front of the tool jaws as shown in Figure 2.

so that the die is held in place, but do not tighten the screw completely at this point. Note: The tool ratchet has detents that are

audible as seven “clicks” as the handles are closed. The ratchet releases on the seventh “click”.

sixth “click,” then tighten both die retention screws until snug.

remove the die retention screws and slide the dies out of the tool jaws.

jaw of the frame assembly.

into the stationary jaw of the frame assembly.

sixth “click,” then tighten both die retention screws until snug.

159-32800, 159-32811, 159-32821, 159-32831

Hand Crimping Tool and Dies

Moveable Jaw

Stationary Jaw

Emergency

Ratchet

Release

Available from Mouser Electronics

1-800-346-6873 / www.mouser.com

Ratchet Adjustment

Wheel

Pivot Pin

Ratchet Adjustment

Screw

Die Retaining

Screws

159-32800

Figure 1

KC-301314

159-32821 Summary of contents

Page 1

... Hand Crimping Tool and Dies 159-32800, 159-32811, 159-32821, 159-32831 Stationary Jaw Moveable Jaw Emergency Ratchet Release INTRODUCTION. This instruction sheet provides application and maintenance procedures for the Hand Crimping Tool. (See Figure 1.) This tool is designed to acept interchangeable crimping die assemblies. Read these instructions thoroughly before installing dies and using the tool ...

Page 2

... Hand Crimping Tool and Dies 159-32800, 159-32811, 159-32821, 159-32831 4. MAINTENANCE / INSPECTION 4.1 Daily Maintenance. Operators of this tool must be made aware of, and responsible for, the following steps of daily maintenance: 1. Remove dust, moisture, and any other contaminants from the tool with a clean, soft brush clean, soft, lint–free cloth. ...