DEHR33D102KN3A Murata Electronics North America, DEHR33D102KN3A Datasheet - Page 21

• Manufacturer Part Number: DEHR33D102KN3A
• Description: CAP CER 2000VDC R RAD
• Manufacturer: Murata Electronics North America
• Series: DEHr

Specifications of DEHR33D102KN3A

• Voltage - Rated: 2000V (2kV)
• Lead Style: *
• Capacitance: 1000pF
• Tolerance: ±10%
• Temperature Coefficient: R
• Mounting Type: *
• Operating Temperature: -25°C ~ 125°C
• Features: High Voltage, Low Dissipation Factor
• Applications: General Purpose
• Package / Case: *
• Size / Dimension: *
• Thickness: *
• Lead Spacing: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Ratings: -

!Note
No.
10
11
12
13
14
15
*
1
"Room condition" Temperature: 15 to 35 C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
Continued from the preceding page.
Soldering
Effect
(Non-Preheat)
Soldering
Effect
(On-Preheat)
Vibration
Resistance
Solvent
Resistance
Humidity
(Under
Steady
State)
Humidity
Insulation
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
DEJ Series (Which Meet Japanese Law) Specifications and Test Methods
Item
Appearance
I.R.
Dielectric
Strength
Appearance
I.R.
Dielectric
Strength
Appearance
Capacitance
D.F.
Appearance
Appearance
Capacitance
Change
D.F.
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
D.F.
I.R.
Dielectric
Strength
No marked defect
1000M min.
Per Item 6
No marked defect
1000M min.
Per Item 6
No marked defect
Within the specified tolerance
No marked defect
No marked defect
1000M min.
Per Item 6
No marked defect
1000M min.
Per Item 6
Char.
Char.
Char.
Char.
Char.
E
F
E
F
E
F
E
F
E
F
Capacitance Change
Capacitance Change
Specifications
Specifications
Specifications
Specifications
Within 20%
Within 30%
Within 20%
Within 30%
D.F.V2.5%
D.F.V5.0%
D.F.V5.0%
D.F.V7.5%
D.F.V5.0%
D.F.V7.5%
DEJ Series Specifications and Test Methods
As shown in the figure, the lead
wires should be immersed in
solder of 350 10˚C up to 1.5 to
2.0mm from the root of terminal for
3.5 0.5 sec.
Pre-treatment:
Post-treatment:
First the capacitor should be
stored at 120+0/-5 C for
60+0/-5 sec.
Then, as in the figure, the lead
wires should be immersed in
solder of 260+0/-5 C up to 1.5 to
2.0mm from the root of terminal
for 7.5+0/-1 sec.
Pre-treatment:
Post-treatment:
The capacitor should be firmly soldered to the supporting lead
wire and vibrated at a frequency range of 10 to 55Hz, 1.5mm in
total amplitude, with about a 1-minute rate of vibration change
from 10Hz to 55Hz and back to 10Hz.
Apply for a total of 6 hrs., 2 hrs. each in 3 mutually perpendicular
directions.
The capacitor should be immersed into a isopropyl alcohol for
30 5 sec.
Set the capacitor for 500 12 hrs. at 40 2˚C in 90 to 95%
relative humidity.
Pre-treatment:
Post-treatment:
The capacitor should be subjected to 40 2˚C, relative humidity
of 90 to 98% for 8 hrs., and then removed in room temperature
for 16 hrs. until 5 cycles are completed.
Pre-treatment:
Post-treatment:
Capacitor should be stored at 85 2˚C for 1 hr., then placed at
room condition*
Capacitor should be stored for 4 to 24 hrs. at room
condition.*
Capacitor should be stored at 85 2˚C for 1 hr., then placed at
room condition*
Capacitor should be stored for 4 to 24 hrs. at
room condition.*
Capacitor should be stored at 85 2˚C for 1 hr., then placed at
room condition*
Capacitor should be stored for 1 to 2 hrs. at room condition.*
Capacitor should be stored at 85 2˚C for 1 hr., then placed at
room condition*
Capacitor should be stored for 1 to 2 hrs. at room condition.*
1
1
1
1
1
1
for 24 2 hrs. before initial measurements.
for 24 2 hrs. before initial measurements.
for 24 2 hrs. before initial measurements.
for 24 2 hrs. before initial measurements.
Test Method
Continued on the following page.
Thermal
Screen
Thermal
Screen
Capacitor
Capacitor
Molten
Solder
Molten
Solder
1.5
to 2.0mm
1.5
to 2.0mm
19
1
1
C85E.pdf
Jul.13,2011
5