MM8430-2610RA1 Murata Electronics North America, MM8430-2610RA1 Datasheet - Page 21
![CONN MW COAXIAL WITH SWITCH SMD](/photos/2/12/21234/mm8430-2610ra1_sml.jpg)
MM8430-2610RA1
Manufacturer Part Number
MM8430-2610RA1
Description
CONN MW COAXIAL WITH SWITCH SMD
Manufacturer
Murata Electronics North America
Series
8430r
Datasheet
1.MM8430-2610RA1.pdf
(39 pages)
Specifications of MM8430-2610RA1
Connector Style
SWD
Connector Type
Jack, Female Sockets
Contact Termination
Solder
Impedance
50 Ohm
Mounting Type
Surface Mount
Fastening Type
Push-Pull
Frequency - Max
6GHz
Features
Internal Switch
Frequency-max
6GHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Color
-
Cable Group
-
Other names
490-4980-2
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MM8430-2610RA1
Manufacturer:
MURATA
Quantity:
1 000
Company:
Part Number:
MM8430-2610RA1
Manufacturer:
COPAL
Quantity:
429
Part Number:
MM8430-2610RA1
Manufacturer:
MURATA/村田
Quantity:
20 000
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1. Reflow soldering
2. Soldering by soldering iron
3. We cannot warrant against mishaps caused by any use
4. In soldering, do not apply excessive mechanical force to
5. Please note the following in case of soldering terminals
6. Please mount this product at the position so that stress
7. Please dry out this product immediately after soldering
Notice (Soldering and Mounting)
Soldering must be carried out without exceeding the
allowable soldering temperature and time shown within
the shaded area of Figure "Allowable Temperature and
Time of Reflow Soldering".
In case the soldering is repeated, the maximum time in
Figure "Allowable Temperature and Time of Reflow
Soldering" should be accumulated time. The standard
soldering conditions are shown in Figure "Reflow
Soldering Standard Conditions".
Use the Pattern and Metal mask pattern is illustrated in
details.
Follow standard solder stencil mask pattern to avoid the
possibility of solder being trapped under connector.
Soldering by soldering iron should be carried out in
accordance to the following conditions.
of this product that deviates from allowable temperature
and time of reflow soldering.
terminals or leads greater than specified in the drawing.
or leads of the product.
by wrap and/or bend of the PCB may not apply to it.
and cleaning.
Pre-heating
Soldering
(1) Use Rosin based flux, but not with strong acid flux
(2) Flux should be thoroughly cleaned from connector
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
(Chlorine content should be less than 0.20wt%).
to prevent possible deterioration of electrical
characteristics.
Temperature
Time
Temperature (at the tip of the soldering
iron) less than 350D
Time
150D
60 to 120 s.
less than 3 s.
Measuring point of temperature : In-Out Terminals of the Device
Reflow Soldering
Allowable Temperature and Time of Reflow Soldering
Reflow Soldering Standard Conditions
240
230
150
100
25
260
250
240
230
220
210
200
190
180
0
Pre-heating 150 20D
30
60-120 sec.
60
Time (sec.)
90
: Both Convection and Infrared Rays
: Hot Air
: Hot Plate
120
Continued on the following page.
Peak temperature 250 5D
150
Solder : Sn-3.0Ag-0.5Cu
30-50 sec.
180
30 sec. max.
210
Time (sec.)
Notice
240
O30E.pdf
19
07.9.3
3