142-0203-011 Emerson Network Power, 142-0203-011 Datasheet - Page 11

• Manufacturer Part Number: 142-0203-011
• Description: CONN RF STRAIGHT CLAMP GOLD SMA
• Manufacturer: Emerson Network Power
• Series: SMAr
• Type: Cable Plugr

Specifications of 142-0203-011

• Connector Style: SMA
• Connector Type: Plug, Male Pins
• Contact Termination: Clamp and Solder
• Impedance: 50 Ohm
• Mounting Type: Free Hanging (In-Line)
• Fastening Type: Threaded
• Cable Group: RG-161, 174, 188, 316
• Frequency - Max: 12.4GHz
• Frequency-max: 12.4GHz
• Body Style: Straight
• Cable Type: RG316
• Features: Captivated Contact
• Rf Series: SMA
• Product: Various Connectors
• Gender: Male
• Contact Plating: Gold
• Shell Plating: Gold
• Termination Style: Clamp
• Angle: Straight
• Finish, Housing: Gold
• Material, Contact: Brass
• Material, Dielectric: TFE
• Material, Housing: Brass
• Primary Type: SMA
• Special Features: Captivated Contact
• Termination: Clamp
• Voltage, Rating: 250 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Color: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 142-0102-011; 142-0221-001; 1420203011; J474

INCHES (MILLIMETERS)
CUSTOMER DRAWINGS AVAILABLE UPON REQUEST
STRAIGHT SMA LOW LOSS DIAMETER 195, .200 AND .240
STRAIGHT TYPE PLUGS
Johnson Components
®
• P.O. Box 1732 • Waseca, MN 56093-0832 • 1-800-247-8256 • Fax: [phone] • www.johnsoncomp.com
1. Identify connector parts. (3 piece parts - except bulkhead)
2. Strip cable to dimensions shown. Do not nick braid, foil or center
3. Assemble contact onto cable as shown. Position contact such that a
4. Flare braid and slide body assembly over contact, foil and dielectric,
conductor. Cut foil flush with dielectric, do not remove foil. Make sure
that dielectric is clean and free from all particles. Tin center conduc-
tor, keeping solder amount to a minimum. Slide crimp sleeve onto
jacket of cable.
gap of no more than .020 (0.51) is kept between dielectric and con-
tact. Solder contact to center conductor through solder hole using
.020 (0.51) Diameter solder. Use a minimum amount of solder for a
good joint. Do not allow contact to move into dielectric during solder-
ing process.
then under braid. Seat body assembly firmly onto contact. Arrange
braid uniformly around crimp stem. Slide crimp sleeve forward and
crimp using Johnson Components
and recommended crimp die hex.
CABLE GROUP PART NUMBER
LMR-195
LMR-240
LMR-200
LMR-195
LMR-240
LMR-200
LMR-240
LMR-200
LMR-195
LMR-240
LMR-200
LMR-195
®
hand crimp tool 141-0000-913
Instructions
Assembly
142-0307-411
142-0307-416
142-0335-401
142-0335-406
142-0339-401
142-0339-406
142-0407-011
142-0407-016
142-0435-001
142-0435-006
142-0439-001
142-0439-006
142-4435-001
142-4435-006
142-4439-001
142-4439-006
142-4407-001
142-4407-006
142-5435-001
142-5435-006
142-5439-001
142-5439-006
142-5407-001
142-5407-006
CRIMP HEX
.213 (5.41)
.213 (5.41)
.213 (5.41)
.240 (6.10)
.240 (6.10)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.240 (6.10)
.240 (6.10)
.213 (5.41)
.213 (5.41)
.240 (6.10)
.240 (6.10)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.255 (6.48)
.255 (6.48)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.213 (5.41)
11