CM1402-03CP ON Semiconductor, CM1402-03CP Datasheet
CM1402-03CP
Specifications of CM1402-03CP
Available stocks
Related parts for CM1402-03CP
CM1402-03CP Summary of contents
Page 1
... This device is particularly well suited for portable electronics (e.g. mobile handsets, PDAs, notebook computers) because of its small package format and easy-to-use pin assignments. In particular, the CM1402 is ideal for EMI filtering and protecting data lines from ESD for the SIM card slot in mobile handsets. ...
Page 2
... Electrical Schematic Rev Page www.onsemi.com CM1402 ...
Page 3
... EMI Filter with ESD Protection for DAT Signal EMI Filter with ESD Protection for DAT Signal ESD Protection Channel - V CC ESD Protection Channel PART NUMBERING INFORMATION Ordering Part Number CM1402-03CP ABSOLUTE MAXIMUM RATINGS Rev Page www.onsemi.com Supply Lead-free Finish 1 Part Marking ...
Page 4
... Note 4: Unused pins are left open. CONDITIONS V = 2.5VDC, 1MHz, IN 30mV 10μ 3.3V BIAS I = 10mA LOAD I = -10mA LOAD Notes 2 and 4 Notes 2,3, and 100Ω 20pF R = 47Ω 20pF Rev Page www.onsemi.com CM1402 RATING UNITS -40 to +85 °C 1 MIN TYP MAX UNITS Ω 80 100 120 Ω ...
Page 5
... CM1402 Performance Information Typical Filter Performance (nominal conditions unless specified otherwise, 50 Ohm Environment) Figure 1. A1-C1 EMI Filter Performance Rev Page www.onsemi.com ...
Page 6
... Figure 2. A2-C2 EMI Filter Performance Rev Page www.onsemi.com CM1402 ...
Page 7
... CM1402 Performance Information (cont’d) Typical Filter Performance (nominal conditions unless specified otherwise, 50 Ohm Environment) Figure 3. A3-C3 EMI Filter Performance Rev Page www.onsemi.com ...
Page 8
... Figure 4. Typical Diode Capacitance vs. Input Voltage (normalized to 2.5VDC) Rev Page www.onsemi.com CM1402 ...
Page 9
... CM1402 Application Information The CM1402 provides a bidirectional filter and protector for all the signals and the power line on the SIM (subscriber identity module) card connector. SIM cards are found in all GSM cellular phones and in some other handheld devices or card readers. The ESD diodes protect the controller against possible ESD strikes that may occur when the connector pins are exposed during direct contact, or during insertion of the SIM card into the card slot ...
Page 10
... Figure 6. Lead-free (SnAgCu) Solder Ball Reflow Profile N on-Solder M ask D efined Pad 0.240m m D IA. Solder Stencil Opening 0.300m m D IA. Solder Mask Opening 0.290m m D IA. Rev Page www.onsemi.com CM1402 VALUE 0.240mm Round Non-Solder Mask defined pads 0.290mm Round 0.125mm - 0.150mm 0.300mm Round 50/50 by volume ...
Page 11
... CM1402 CSP Mechanical Specifications CM1402 devices are packaged in a custom Chip Scale Package (CSP). Dimensions are presented below. For complete information on CSP packaging, see the California Micro Devices CSP Package Information document. PACKAGE DIMENSIONS Custom CSP Package Bumps Millimeters Dim Min ...
Page 12
... X 1.45 X 0.711 8mm N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 Rev Page www.onsemi.com CM1402 REEL QTY PER DIAMETER REEL 178mm (7") 3500 4mm 4mm ON Semiconductor Website: www ...