31-318 AMPHENOL RF, 31-318 Datasheet
31-318
Specifications of 31-318
ARF1139
Related parts for 31-318
31-318 Summary of contents
Page 1
... Slide outer ferrule over braid and up against connector body. Crimp outer ferrule using Die Set Cavity specified in table above. 279 Amphenol ® Stripping Dimensions, inches (mm .437(11.1) .312(7.9) .248(6.3) .125(3.2) .437(11.1) .312(7.9) .248(6.3) .125(3.2) .437(11.1) .312(7.9) .248(6.3) .125(3.2) www.amphenolrf.com ...
Page 2
... Not supplied on all items Step 1 a Step 2 Step 3 Step 4 Step 5 For angle plugs only: (except 31-204) Solder center conductor to preassembled contact. Assemble cap and lightly punch center of cap for retention in body, or solder in place. Amphenol Corporation Tel: 800-627-7100 clamp bushing‡ female contact jack body ‡ ...
Page 3
... Slide outer ferrule onto cable as shown. For RG-174, 179, 187, 188, 316/U cables only, slit jacket back .100"(2.5mm) as shown. Before attaching center contact, slide metal spacer/TFE sleeve (not shown) over cable dielectric and under braid. The center contact should butt against the dielectric and TFE sleeve ...
Page 4
... BNC Jack 174, 188, 316 31-318 BNC Bulkh. Jack 174, 188, 316 31-318-RFX BNC Bulkh. Jack 174, 188, 316 31-318-1001 BNC Bulkh. Jack Dbl. Br. 316 31-245-RFX BNC Bulkh. Jack 179, 187 31-334 BNC Angle Plug 55, 142, 223, 400 31-335 ...
Page 5
... Cable Number Type RG-/U 31-351 BNC Plug 58, 141 31-359 BNC Plug 59, 62, 140 31-371 BNC Plug 174, 179, 187, 188, 316 boot Step 1 outer ferrule Step 2 Step 3 outer ferrule must Step 4 clamp nut assy as shown Step 5 note: center conductor must be visible thru contact solder ...
Page 6
... BNC Plug 59 31-5137 BNC Plug 58 31-5137-RFX BNC Plug 58 Step 1 Strip cable as shown. Take care not to nick center conductor or outer braid. Step 2 Twist outer braid in a clockwise direction so that at least min. of cable 1/32" of cable dielectric is bared, and braid is left flat. (Stray dielectric or loose braid can cause shorts ...
Page 7
... Slide clamp nut over cable. Strip cable to dimension shown. Cut braid and dielectric square. Do not nick center conductor. Step 1B For 31-4541-RFX.. Same as step 1A except use Step 1B strip dimensions, and then slit jacket back .125"(3.2 mm) in four places 90° apart as shown in illustration. ...
Page 8
... Connector Cable Number Type RG-/U 31-4700 BNC Plug 58, 141 31-4702 BNC Plug 59 .250(6.4) .156(4.0) Step 1 Slide ferrule over cable end, slotted end first. Strip cable to dimensions shown. Do not nick center conductor. Flare braid slightly as shown. Step 2 Tin exposed center conductor. Solder center contact on center conductor ...
Page 9
... Belden 8281, 9231 a Step 1 For RG-174, 179, 187, 188, 316/U cables only, slit jacket back .100"(2.5mm) as shown. Before attaching center contact, slide TFE sleeve (not shown) over cable dielectric and under braid. The center contact should butt against the dielectric and TFE sleeve. ...
Page 10
... BNC Plug Quad Shield 59 Step 1 For RG-174, 179, 187, 188, 316/U cables only, slit jacket back .100"(2.5mm) as shown. Before attaching center contact TFE sleeve (not shown) over cable dielectric and under braid. For 31-71016, before attaching center contact. Slide metal spacer/TFE sleeve (not shown) over cable dielectric and under braid ...