1045481-1 Tyco Electronics, 1045481-1 Datasheet
1045481-1
Manufacturer Part Number
1045481-1
Description
CONN PLUG SMA RG 174 STR SOLDER
Manufacturer
Tyco Electronics
Series
SMAr
Datasheet
1.1045481-1.pdf
(2 pages)
Specifications of 1045481-1
Connector Style
SMA
Connector Type
Plug, Male Pins
Contact Termination
Solder
Impedance
50 Ohm
Mounting Type
Free Hanging (In-Line)
Fastening Type
Threaded
Cable Group
RG-174, 179, 187, 188, 316
Frequency - Max
12.4GHz
Frequency-max
12.4GHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
Color
-
1. INTRODUCTION
These instructions cover the assembly of the SSMA
Straight Cable Plugs listed in Figure 1. Figure 1 also
lists the cable types required for the various
connectors.
All of these connectors are solder–type connectors.
Tooling required for the application is listed in
Figure 2.
2. ASSEMBLY
2.1. Preparing the Coaxial Cable End
E
All International Rights Reserved
AMP and Tyco are trademarks. *Trademark
Other products, logos, and company names used are the property of their respective owners.
PART NUMBER
ELECTRONICS
Housing Subassembly
2004 Tyco Electronics Corporation, Harrisburg, PA
NOTE
NOTE
1. Place the heat–shrink tubing and ferrule on the
cable.
1055463–1
1055461–1
TYCO
ELECTRONICS PART NUMBER
Dimensions in this document are in metric units
[with U.S. customary units in brackets], unless
otherwise specified.
Reasons for revision can be found in
SECTION 3.
1062258–1
1081231–1
1045481–1
1045482–1
PREVIOUS PART
TYCO
2098 5237 10
2098 5236 02
NUMBER
(T–4579)
(T–1888)
Figure 2
Center Contact Holder
Locator Tool
CONNECTOR
This controlled document is subject to change.
For latest revision, call the FAX/PRODUCT INFO number.
(Figure 3)
DESCRIPTION
SSMA Straight Cable Plug Connectors
Center Contact
PREVIOUS PART NUMBER
Figure 1
1031 5002 95
1031 5002 00
1031 5002 00
1031 5002 02
2.2. Soldering Center Contact to Inner Conductor
(Figure 4)
2.3
[.090]
Inner
Conductor
2. Remove the end portion of the cable jacket to
expose the cable braid.
3. Trim the braid to the length shown in Figure 3.
4. Trim the cable dielectric to length.
5. Trim the inner conductor to length.
6. Flare the cable braid.
1. Tin the inner conductor
2. Place center contact in center contact holder
(see Figure 4)
3. Heat the center contact with a soldering iron and
carefully push it over the inner conductor to rest
firmly against the dielectric.
Ferrule
Dielectric
TOOLING ASSISTANCE CENTER 1–800–722–1111
FAX/PRODUCT INFO 1–800–522–6752
For Regional Customer Service, visit our website at
www.tycoelectronics.com
Figure 3
Ferrule
5.1
[.200]
9.14
[.360]
RG174/U, 179
187, 188, 316
Heat–Shrink Tubing
CABLE
TYPE
Heat–Shrink Tubing
ABLE
4
Instruction Sheet
408–4790
24 MAR 04 Rev A
(was A.P. 10–010)
Cable
Jacket
1 of 2
LOC B
Related parts for 1045481-1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Battery Interconnection System for Portable Electronics; BU CONN FS6 8POS DIP TYPE ASSY ( AMP )
Manufacturer:
Tyco Electronics
Part Number:
Description:
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
HOLDER BATTERY COIN 23MM 1-CELL
Manufacturer:
Keystone Electronics
Datasheet:
Part Number:
Description:
Manufacturer:
Tyco Electronics
Datasheet:
1045481-1 Summary of contents
Page 1
... Housing Subassembly CONNECTOR TYCO ELECTRONICS PART NUMBER 1062258–1 1081231–1 1045481–1 1045482–1 1. INTRODUCTION These instructions cover the assembly of the SSMA Straight Cable Plugs listed in Figure 1. Figure 1 also lists the cable types required for the various connectors. All of these connectors are solder–type connectors. ...
Page 2
Center Contact Holder T–4579 Center Contact Pin Heat Here Cable Dielectric Figure 4 To avoid personal injury, be sure to follow all local DANGER safety practices when using soldering equipment. 4. Remove the excess solder or splatter. 2.3. Soldering Cable ...