S48SP3R310NRFB Delta Electronics, S48SP3R310NRFB Datasheet - Page 7

no-image

S48SP3R310NRFB

Manufacturer Part Number
S48SP3R310NRFB
Description
MODULE DC/DC 1X1 BRICK 3.3V 10A
Manufacturer
Delta Electronics
Series
Delphi S48SPr
Type
Isolated with Remote On/Off and UVLOr
Datasheet

Specifications of S48SP3R310NRFB

Operating Temperature
-40°C ~ 110°C
Power (watts) - Rated
33W
Efficiency
90%
Approvals
CE, cUL, TUV, UL
Output
3.3V
Number Of Outputs
1
Power (watts)
35W
Mounting Type
Through Hole
Voltage - Input
36 ~ 75V
Package / Case
6-DIP Module, 1x1 Brick
1st Output
3.3 VDC @ 10A
Size / Dimension
1.30" L x 0.96" W x 0.34" H (33mm x 24.4mm x 8.55mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
2nd Output
-
3rd Output
-
4th Output
-
Other names
941-1043
DESIGN CONSIDERATIONS
Input Source Impedance
The impedance of the input source connecting to the
DC/DC power modules will interact with the modules
and affect the stability. A low ac-impedance input source
is recommended. If the source inductance is more than
a few μH, we advise adding a 10 to 100 μF electrolytic
capacitor (ESR < 0.7 Ω at 100 kHz) mounted close to
the input of the module to improve the stability.
Layout and EMC Considerations
Delta’s DC/DC power modules are designed to operate
in a wide variety of systems and applications. For design
assistance with EMC compliance and related PWB
layout issues, please contact Delta’s technical support
team. An external input filter module is available for
easier EMC compliance design. Application notes to
assist designers in addressing these issues are pending
release.
Safety Considerations
The power module must be installed in compliance with
the spacing and separation requirements of the
end-user’s safety agency standard, i.e., UL60950,
CAN/CSA-C22.2 No. 60950-00 and EN60950:2000 and
IEC60950-1999, if the system in which the power
module is to be used must meet safety agency
requirements.
Basic insulation based on 75 Vdc input is provided
between the input and output of the module for the
purpose of applying insulation requirements when the
input to this DC-to-DC converter is identified as TNV-2
or SELV.
source is other than TNV-2 or SELV.
When the input source is SELV circuit, the power
module
requirements. If the input source is a hazardous voltage
which is greater than 60 Vdc and less than or equal to
75 Vdc, for the module’s output to meet SELV
requirements, all of the following must be met:
DS_S48SP3R310_05222008
meets
An additional evaluation is needed if the
SELV
(safety
extra-low
voltage)
When installed into a Class II equipment (without
grounding), spacing consideration should be given to
the end-use installation, as the spacing between the
module and mounting surface have not been evaluated.
The power module has extra-low voltage (ELV) outputs
when all inputs are ELV.
This power module is not internally fused. To achieve
optimum safety and system protection, an input line fuse
is highly recommended. The safety agencies require a
fuse with 3A maximum rating to be installed in the
ungrounded lead. A lower rated fuse can be used based
on the maximum inrush transient energy and maximum
input current.
Soldering and Cleaning Considerations
Post solder cleaning is usually the final board assembly
process before the board or system undergoes electrical
testing. Inadequate cleaning and/or drying may lower the
reliability of a power module and severely affect the
finished circuit board assembly test. Adequate cleaning
and/or drying is especially important for un-encapsulated
and/or open frame type power modules. For assistance
on appropriate soldering and cleaning procedures,
please contact Delta’s technical support team.
mains by reinforced or double insulation.
accessible.
one Vo pin shall also be grounded.
where the module is used, in combination with the
module, to ensure that under a single fault,
hazardous voltage does not appear at the module’s
output.
The input source must be insulated from the ac
The input terminals of the module are not operator
If the metal baseplate is grounded, one Vi pin and
A SELV reliability test is conducted on the system
7

Related parts for S48SP3R310NRFB