AD9226-EB Analog Devices Inc, AD9226-EB Datasheet
AD9226-EB
Specifications of AD9226-EB
Related parts for AD9226-EB
AD9226-EB Summary of contents
Page 1
... MSPS data rates. There are no missing codes over the full operating temperature range (guaranteed). The input of the AD9226 allows for easy interfacing to both imaging and communications systems. With a truly differential input structure, the user can select a variety of input ranges and offsets including single-ended applications ...
Page 2
... IDRVDD 4, 5 POWER CONSUMPTION NOTES 1 Includes internal voltage reference error. 2 Excludes internal voltage reference error. 3 Load regulation with 1 mA load current (in addition to that required by the AD9226). 4 AVDD = DRVDD = 3 V Specifications subject to change without notice MSPS, VREF = 2.0 V, Differential inputs, T SAMPLE Temp ...
Page 3
... Pipeline Delay (Latency) 3 Output Enable Delay NOTES The clock period may be extended to 10 µs without degradation in specified performance @ 25° When MODE pin is tied to AVDD or grounded, the AD9226 SSOP is not affected by clock duty cycle. 3 LQFP package. Specifications subject to change without notice. ANALOG INPUT CLOCK ...
Page 4
... AD9226–SPECIFICATIONS AC SPECIFICATIONS (AVDD = 5 V, DRVDD = Parameter SIGNAL-TO-NOISE RATIO f = 2.5 MHz MHz MHz MHz 200 MHz IN SIGNAL-TO-NOISE RATIO AND DISTORTION f = 2.5 MHz MHz MHz MHz 200 MHz IN TOTAL HARMONIC DISTORTION f = 2.5 MHz MHz MHz MHz 200 MHz IN SECOND AND THIRD HARMONIC DISTORTION ...
Page 5
... Temperature Range AD9226ARS –40°C to +85°C AD9226AST –40°C to +85°C AD9226-EB AD9226-LQFP-EB CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD9226 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high-energy electrostatic discharges ...
Page 6
... PIN CONNECTION 28-Lead SSOP CLK 1 28 DRVDD (LSB) BIT 12 2 DRVSS 27 BIT AVDD BIT AVSS BIT VINB BIT VINA AD9226 BIT MODE TOP VIEW (Not to Scale) BIT CAPT BIT CAPB BIT REFCOM (AVSS) BIT 3 11 VREF 18 BIT SENSE (MSB) BIT 1 ...
Page 7
... The ratio of the rms value of either input tone to the rms value of the peak spurious component. The peak spurious component may or may not be an IMD product. May be reported in dBc (i.e., degrades as signal levels are lowered dBFS (always related back to converter full scale). AD9226 ...
Page 8
... AD9226 DRVDD AVDD AVSS DRVDD DRVDD DRVSS DRVSS AVDD AVSS AVDD AVSS ...
Page 9
... ENOB = 11.3BITS THD = –85dBc –30 SFDR = 87.6dBc –40 –50 –60 –70 –80 –90 –100 –110 –120 0 6.5 13 19.5 FREQUENCY – MHz Typical Performance Characteristics–AD9226 = Differential Input Span 100 SNR = 69.9dBc SINAD = 69.8dBc 90 ENOB = 11.4BITS THD = –86.4dBc SFDR = 88.7dBc 32.5 –30 ...
Page 10
... AD9226 75 2V SPAN, DIFFERENTIAL SPAN, SINGLE-ENDED FREQUENCY – MHz –45 2V SPAN, SINGLE-ENDED –50 –55 –60 –65 –70 –75 –80 –85 – FREQUENCY – MHz 72 – FREQUENCY – MHz 12 11 SPAN, DIFFERENTIAL 68 10 SPAN, SINGLE-ENDED 65 8 8.1 62 7.3 61 100 1000 1 95 ...
Page 11
... SFDR – CLOCK STABILIZER OFF 75 SINAD – CLOCK STABILIZER 0.8 0.6 0.4 0.2 0 –0.2 –0.4 –0.6 –0.8 –1 3500 4000 500 0 AD9226 f = 2MHz 20MHz SAMPLE RATE – MSPS SFDR – CLOCK STABILIZER ON SINAD – CLOCK STABILIZER OFF POSITIVE DUTY CYCLE 1k 1500 2k 2500 3k ...
Page 12
... AD9226 AD9226–Typical IF Sampling Performance Characteristics (AVDD = 5.0 V, DRVDD = 3 MSPS with CLK Stabilizer Enabled, T SAMPLE V = 2.0 V, unless otherwise noted.) REF 0 SNR = 70.2dBFS –10 SFDR = 89dBFS NOISE FLOOR = 145.33dBFS/Hz –20 –30 –40 –50 –60 –70 –80 –90 –100 –110 –120 FREQUENCY – MHz 0 SNR = 68 ...
Page 13
... SFDR – 2V SPAN 80 75 SNR/NOISE FLOOR – 2V SPAN 70 65 SNR/NOISE FLOOR – 1V SPAN –24 –21 1000 AD9226 165.1 SFDR – 2V SPAN 160.1 155.1 150.1 SNR/NOISE FLOOR – 2V SPAN 145.1 140.1 135.1 –18 –15 –12 –9 –6 A – dBFS IN 160.1 155 ...
Page 14
... SENSE REFCOM OVERVIEW OF INPUT AND REFERENCE CONNECTIONS The overall input span of the AD9226 is equal to the potential at the VREF pin. The VREF potential may be obtained from the internal AD9226 reference or an external source (see Reference Operation section). In differential applications, the center point of the span is obtained by the common-mode level of the signals ...
Page 15
... F the Nyquist frequency (i.e., f The circuit shown in Figure ideal method of applying 0 differential dc drive to the AD9226. It uses an AD8138 to derive a differential signal from a single-ended one. Figure 6b 0.1 F illustrates its performance. Figure 7 presents the schematic of the suggested transformer circuit. The circuit uses a Minicircuits RF transformer, model T1-1T, which has an impedance ratio of four (turns ratio of 2). The schematic assumes that the signal source has a 50 Ω ...
Page 16
... Various high- speed performance amplifiers that are restricted to +5 V/–5 V operation and/or specified for 5 V single-supply operation can be easily configured for the input span of the AD9226. Simple AC Interface Figure 9a shows a typical example of an ac-coupled, single- ended configuration of the SSOP package. The bias voltage ...
Page 17
... F Figure 11a shows a simplified model of the internal voltage refer- VREF ence of the AD9226. A reference amplifier buffers fixed reference. The output from the reference amplifier, A1, appears on the VREF pin. The voltage on the VREF pin determines 0.1 F the full-scale input span of the ADC ...
Page 18
... VREF. Thus the valid input range extends from (VREF + VREF/2) to (VREF – VREF/2). For example, if the REF191, a 2.048 V external reference, is selected, the input span extends to 2.048 V. In this case, 1 LSB of the AD9226 corresponds to 0.5 mV essential that a minimum µF capacitor, in parallel with a 0.1 µF low-inductance ceramic capacitor, decouple the reference output to ground ...
Page 19
... connected to AVDD, the output data format will be two’s complement. See Table II. Pin 43 of the LQFP package controls the clock stabilizer function of the AD9226. If the pin is connected to AVSS, both clock edges will be used in the conversion architecture. When Pin 43 is connected to AVDD, the internal duty cycle will be determined by the clock stabilizer function within the ADC ...
Page 20
... Bias Decoupling The CML and VR are analog bias points used internally by the AD9226. These pins must be decoupled with at least a 0.1 µF DRVDD = 3V capacitor as shown in Figure 18. The dc level of CML is approxi- mately AVDD/2. This voltage should be buffered used for any external biasing ...
Page 21
... CLOCK and AUXCLK. The CLOCK input should be selected if the frequency of the input clock signal is at the target sample rate of the AD9226. The input clock signal is ac-coupled and level-shifted to the switch- ing threshold of a 74VHC02 clock driver. The AUXCLK input should be selected in applications requiring the lowest jitter and SNR performance (i ...
Page 22
... DUTAVDD C23 RED C38 C41 10 F 0.1 F 0.001 F AVDD 10V RED DUTDRVDD DUTDRVDD 10V RED DVDD TP11 TP12 TP13 TP14 BLK BLK BLK BLK AD9226LQFP 3 28 OTR0 AVDD1 OTR 4 27 D130 AVDD2 MSB- AVSS1 B2 D120 2 25 D110 AVSS2 D100 SENSE B4 37 ...
Page 23
... D11 A3 Y3 1N5712 5 15 D10 C11 0.1 F C26 C18 10V 0 10V 74VHC541 VCC GND DUTCLK OTR JP4 JP3 2 AVDD C3 C10 10 F 0.1 F 10V U8 DECOUPLING AD9226 DVDD RP1 RP1 RP1 RP1 RP1 RP1 RP1 RP1 RP2 RP2 RP2 RP2 RP2 RP2 RP2 ...
Page 24
... AD9226 RP3 OTRO OTR RP3 D130 D13 RP3 D120 D12 RP3 D110 D11 RP4 C15 AVDD 10 F D100 D10 RP4 10V D90 D9 RP4 C69 0.1 F D80 D8 RP4 R37 D70 D7 499 3 R34 VCC 523 1 4 –W VO AMP INPUT U2 R35 S2 VO– 499 ...
Page 25
... AD9226 ...
Page 26
... AD9226 ...
Page 27
... AD9226 ...
Page 28
... AD9226 28-Lead Shrink Small Outline (RS-28) 0.407 (10.34) 0.397 (10.08 0.07 (1.79) 0.078 (1.98) PIN 1 0.066 (1.67) 0.068 (1.73) 0.0256 0.015 (0.38) 0.008 (0.203) SEATING 0.009 (0.229) (0.65) 0.010 (0.25) PLANE 0.002 (0.050) BSC 0.005 (0.127) OUTLINE DIMENSIONS Dimensions shown in inches and (mm). ...