CONREVSMA005-R178 Linx Technologies Inc, CONREVSMA005-R178 Datasheet - Page 20

• Manufacturer Part Number: CONREVSMA005-R178
• Description: CONN RPSMA FML BLKHD REAR RG178
• Manufacturer: Linx Technologies Inc
• Series: RP-SMAr

Specifications of CONREVSMA005-R178

• Connector Style: RP-SMA
• Connector Type: Jack, Male Pins
• Contact Termination: Crimp and Solder
• Impedance: 50 Ohm
• Mounting Type: Panel Mount, Bulkhead - Front Side Nut
• Fastening Type: Threaded
• Cable Group: RG-178
• Frequency - Max: 12.4GHz
• Frequency-max: 12.4GHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Color: -

DESCRIPTION
The BBA Series is a family of low-cost high-
performance broadband RF amplifiers.
modules are ideally suited to a wide range of
amplification
including extending the range of Linx’s own RF
modules (where legally appropriate). Housed in
a compact SMD package, the hybrid amps are
matched
impedances. The modules utilize a GaHBT gain
stage, which yields high gain and IP3, excellent
flatness, and low noise. The BBA-519-A is the
high power model and is suitable for the final
gain stage in a transmitter. This amplifier can
boost the output power of a transmitter to much
higher levels and provide a significant increase in range (where legally appropriate).
FEATURES
APPLICATIONS INCLUDE
Page 36
TX / RX Range Enhancement*
Prematched for 50Ω impedance
No external RF components
Exceptional gain flatness
Compact SMD package
High output
4.8dB noise figure
IF or RF Buffering
Driver or Final Stage for PA
General Purpose Gain Blocks
required
WIRELESS MADE SIMPLE
to
and
50-ohm
®
buffering
BBA SERIES
HIGH POWER AMPLIFIER
source
applications,
and
*NOTE
that approvals may be required by applicable governing
bodies for systems producing RF energy. It is the
responsibility of the user to determine and adhere to
the appropriate regulations for the region in which
operation is intended.
load
The
PART #
BBA-519-A
BBA amplifiers are supplied in tubes of 50 pcs.
ORDERING INFORMATION
* The purchaser of this device should be aware
10MHz to 3GHz broadband
+18dB small signal gain at
Up to +17dB (50mW) linear
Operates from a single supply
operation
900MHz
output power
0.130"
0.360"
Typ.
PHYSICAL DIMENSIONS
DESCRIPTION
High Power RF Amplifier
AMP MODULE
BBA-519-A
LOT 0100
0.500"
Notes
1. All parameters measured at 5.0V, 25°C, -50dBm input.
2. 5.2V to 12V range is possible with the appropriate current limiting resistor.
3. T = 25°C, I
4. 100MHz to 2,000MHz.
5. At 2,000MHz.
6. In a 50Ω system, DC to 4,000MHz.
7. At 1,000MHz ± 50kHz, P
8. At 1,000MHz.
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL SPECIFICATIONS
Parameter
POWER SUPPLY
Operating Voltage
Supply Current
AMPLIFIER SECTION
Frequency Range
Gain:
Gain Ripple
Noise Figure
Input VSWR
Output VSWR
Output IP3
Output P
Reverse Isolation
ANTENNA PORT
RF Input Impedance
ENVIRONMENTAL
Operating Temperature Range
@ 100MHz
@ 1,000MHz
@ 2,000MHz
@ 3,000MHz
@ 4,000MHz
1dB
Supply Voltage V
Supply Current
RF Input
Operating Temperature
Storage Temperature
Soldering Temperature
*NOTE*
damage to the device. Furthermore, extended operation at these maximum
ratings may reduce the life of this device.
CC
= 65mA.
Exceeding any of the limits of this section may lead to permanent
TONE
CC
= -10dBm.
Designation
V
R
I
F
CC
–
–
–
–
–
–
–
–
–
CC
IN
C
Min.
4.8
-50
10
–
–
–
–
–
–
–
–
–
–
–
–
–
–
0
+4.8
-60
0
+225°C for 10 seconds
Typical
+18.5
60.0
18.5
17.5
15.5
13.5
12.5
+33
4.8
2.1
1.8
±2
20
50
–
–
–
–
120
+13
to
to
to
4,000
Max.
65.0
+50
+70
5.2
+150
+5.2
–
–
–
–
–
–
–
–
–
–
–
–
–
+70
Units
VDC
MHz
dBm
dBm
kHz
VDC
mA
dBm
dB
dB
dB
dB
dB
dB
dB
dB
°
Ω
–
–
C
mA
°C
°C
Page 37
Notes
2
–
3
–
–
–
–
–
–
4
5
6
6
7
8
5
–
–