GRM32ER72A225KA35L Murata, GRM32ER72A225KA35L Datasheet - Page 216
![Multilayer Ceramic Capacitors (MLCC) - SMD/SMT 1210 2.2uF 100volts X7R 10%](/photos/16/29/162950/055p01_sml.jpg)
GRM32ER72A225KA35L
Manufacturer Part Number
GRM32ER72A225KA35L
Description
Multilayer Ceramic Capacitors (MLCC) - SMD/SMT 1210 2.2uF 100volts X7R 10%
Manufacturer
Murata
Series
GRMr
Datasheet
1.GNM1M2R61A105ME14D.pdf
(221 pages)
Specifications of GRM32ER72A225KA35L
Voltage Rating
100 Volts
Operating Temperature Range
- 55 C to + 125 C
Temperature Coefficient / Code
X7R
Product
General Type MLCCs
Dimensions
2.5 mm W x 3.2 mm L x 2.5 mm H
Termination Style
SMD/SMT
Capacitance
2.2 uF
Tolerance
10 %
Package / Case
1210 (3225 metric)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
GRM32ER72A225KA35L
Manufacturer:
MURATA
Quantity:
640 000
Company:
Part Number:
GRM32ER72A225KA35L
Manufacturer:
MURATA
Quantity:
95 000
Part Number:
GRM32ER72A225KA35L
Manufacturer:
MURATA/村田
Quantity:
20 000
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
Land Layout to Prevent Excessive Solder
2. Mounting of Chips
3. Soldering
(1) Limit of losing effective area of the terminations and
Examples
to Be Avoided
Examples of
Improvements
by the Land
Division
Thickness of adhesives applied
Keep thickness of adhesives applied (50-105 m or more)
to reinforce the adhesive contact considering the
thickness of the termination or capacitor (20-70 m) and
the land pattern (30-35 m).
Mechanical shock of the chip placer
When the positioning claws and pick-up nozzle are worn,
the load is applied to the chip while positioning is
concentrated in one position, thus causing cracks,
breakage, faulty positioning accuracy, etc.
Careful checking and maintenance are necessary to
prevent unexpected trouble.
An excessively low bottom dead point of the suction
nozzle imposes great force on the chip during mounting,
causing cracked chips. Please set the suction nozzle's
bottom dead point on the upper surface of the board.
conditions needed for soldering.
Continued from the preceding page.
Depending on the conditions of the soldering
temperature and/or immersion (melting time),
effective areas may be lost in some parts of the
terminations.
To prevent this, be careful in soldering so that any
possible loss of the effective area on the terminations
will securely remain at a maximum of 25% on all
edge length A-B-C-D-A of part with A, B, C, D, shown
in the Figure below.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Solder Resist
Mounting Close to a Chassis
d
d
1
Chassis
2
Land Pattern
B
Base board
Solder (Ground solder)
d
C
1
<d
Adhesive
2
in section
in section
A
D
Termination
Mounting with Leaded Components
Solder Resist
(2) Flux Application
(3) Solder
An excessive amount of flux generates a large quantity of
Flux containing too high a percentage of halide may
Do not use strong acidic flux.
Do not use water-soluble flux.*
(*Water-soluble flux can be defined as non rosin type flux
flux gas, causing deteriorated solderability. So apply flux
thinly and evenly throughout. (A foaming system is
generally used for flow soldering.)
cause corrosion of the outer electrodes without sufficient
cleaning. Use flux with a halide content of 0.2% max.
including wash-type flux and non-wash-type flux.)
The use of Sn-Zn based solder will deteriorate the
reliability of the MLCC.
Please contact our sales representative or product
engineers on the use of Sn-Zn based solder in advance.
Lead Wire Connected
to a Part Provided
with Lead Wires.
in section
in section
Mounting Leaded Components Later
Continued on the following page.
Solder Resist
Soldering Iron
Lead Wire of
Component to be
Connected Later.
Notice
in section
in section
215
C02E.pdf
10.12.20