LIS331DLHTR STMicroelectronics, LIS331DLHTR Datasheet - Page 30

• Manufacturer Part Number: LIS331DLHTR
• Description: ACCELEROMETER MEMS 3AXIS 16-LGA
• Manufacturer: STMicroelectronics
• Series: MEMS, nanor

Specifications of LIS331DLHTR

• Featured Product: STM32 Cortex-M3 Companion Products
• Axis: X, Y, Z
• Acceleration Range: ± 2g, 4g, 8g
• Sensitivity: 3.9mg/digit, 2mg/digit, 1mg/digit
• Voltage - Supply: 2.16 V ~ 3.6 V
• Output Type: Digital
• Bandwidth: 100Hz ~ 400Hz Selectable
• Interface: I²C, SPI
• Mounting Type: Surface Mount
• Package / Case: 16-LGA
• Package Type: LGA
• Operating Supply Voltage (min): 2.16V
• Operating Supply Voltage (typ): 2.5V
• Operating Supply Voltage (max): 3.6V
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Product Depth (mm): 3mm
• Product Height (mm): 1mm
• Product Length (mm): 3mm
• Mounting: Surface Mount
• Pin Count: 16
• Sensing Axis: X, Y, Z
• Acceleration: 2 g, 4 g, 8 g
• Digital Output - Number Of Bits: 16 bit
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.16 V
• Supply Current: 250 uA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Digital Output - Bus Interface: I2C, SPI
• Mounting Style: SMD/SMT
• Shutdown: Yes
• For Use With: 497-10672 - PLATFORM MUSA497-10048 - BOARD EVAL ACCELEROMETER497-9053 - DEMO BOARD FOR LIS331DLH497-8852 - BOARD DEMO STM8S207R6/LIS331DLH497-8851 - BOARD DEMO STM8S207R6/LIS331DLH
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-10397-2; LIS331DLHTR

Register description
7.7
7.8
7.9
30/38
HP_FILTER_RESET (25h)
Dummy register. Reading at this address zeroes instantaneously the content of the internal
high pass-filter. If the high pass filter is enabled all three axes are instantaneously set to 0g.
This allows to overcome the settling time of the high pass filter.
REFERENCE (26h)
Table 33.
Table 34.
This register sets the acceleration value taken as a reference for the high-pass filter output.
When filter is turned on (at least one of FDS, HPen2, or HPen1 bit is equal to ‘1’) and HPM
bits are set to “01”, filter out is generated taking this value as a reference.
STATUS_REG (27h)
Table 35.
Table 36.
Ref7 - Ref0
ZYXOR
ZOR
YOR
XOR
ZYXDA
ZYXOR
Ref7
REFERENCE register
REFERENCE description
STATUS_REG register
STATUS_REG description
X, Y and Z axis data overrun. Default value: 0
(0: no overrun has occurred;
1: new data has overwritten the previous one before it was read)
Z axis data overrun. Default value: 0
(0: no overrun has occurred;
1: a new data for the Z-axis has overwritten the previous one)
Y axis data overrun. Default value: 0
(0: no overrun has occurred;
1: a new data for the Y-axis has overwritten the previous one)
X axis data overrun. Default value: 0
(0: no overrun has occurred;
1: a new data for the X-axis has overwritten the previous one)
X, Y and Z axis new data available. Default value: 0
(0: a new set of data is not yet available; 1: a new set of data is available)
Reference value for high-pass filter. Default value: 00h.
Ref6
ZOR
Ref5
YOR
Doc ID 15094 Rev 3
XOR
Ref4
ZYXDA
Ref3
Ref2
ZDA
Ref1
YDA
LIS331DLH
Ref0
XDA