58448-3 Tyco Electronics, 58448-3 Datasheet

Pro Crimper II SDE Die Set

58448-3

Manufacturer Part Number
58448-3
Description
Pro Crimper II SDE Die Set
Manufacturer
Tyco Electronics
Series
Pro-Crimper III, AMPLIMITE®r
Type
Pro Crimpersr
Datasheets
1.58448-3.pdf (4 pages)
2.58423-1.pdf (8 pages)
3.58448-2.pdf (5 pages)

Specifications of 58448-3

Wire Size (awg)
28-20
Connector Type
Crimp Terminals
Crimp Handle
A9996-ND
Crimp Or Cable Size
20-28 AWG
Product
Crimping, Stripping & Cutting Tools & Drills
For Use With
Pro Crimper II Crimp Tool & D-Sub 20DF Pin & Socket Contacts AMPLIMITE
Lead Free Status / RoHS Status
na
Lead Free Status / RoHS Status
na, Not applicable / Not applicable
Other names
A9814
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume
applications. A wide selection of powered application equipment for extended- - use, production operations is available.
{ Supplied with die assembly. Also available separately.
} Contact the Tooling Assistance Center or Product Information at the numbers listed below for specific contact part numbers.
1. INTRODUCTION
PRO--CRIMPER III Hand Crimping Tool Assembly
58448--2 consists of Die Assembly 58448--3 and
PRO--CRIMPER III Hand Crimping Tool Frame
354940--1. The die assembly consists of crimping
dies and a locator assembly.
Read these instructions thoroughly before crimping
any contacts.
Reasons for reissue of this instruction sheet are
provided in Section 10, REVISION SUMMARY.
E2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company
All Rights Reserved
TE logo is a trademark.
*Trademark. Other product names, logos, or company names might be trademarks of their respective owners.
The PRO- - CRIMPER III Hand Crimping Tool is a “Commercial” grade tool
and is designed primarily for field installation, repair, maintenance work, or
prototyping in industrial, commercial, or institutional applications. Product
crimped with this tool will meet the crimp height requirement for hand tools in
the appropriate 114 series specification, but may not comply with other feature
parameters of the specification. TE offers a variety of tools to satisfy your
performance requirements. For additional information, contact the Tooling
Assistance Center at 1- - 800- - 722- - 1111.
NOTE
Assembly
58448 3
58448--3
i
TE Die
TE Die
Dimensions in this instruction sheet are in metric
units [with U.S. customary units in brackets].
Figures are not drawn to scale.
Assembly{
1214310 1
1214310--1
Locator
Locator
Front of Tool
(Locator Side)
Die Assembly
Ratchet Adjustment
Wheel
Locator
Assembly
Moving Jaw
PRO- CRIMPER* III Hand Crimping
Tool Assembly 58448- 2
With Die Assembly 58448- 3
Crimp Snap--In Contacts
with Insulation Support
HDP--20 Connector
HDP--20 Connector
Product Family}
AMPLIMITE*
TOOLING ASSISTANCE CENTER 1--800--722--1111
PRODUCT INFORMATION 1--800--522--6752
Figure 1
2. DESCRIPTION
The tool features a tool frame with a stationary jaw
and handle, moving jaw, moving handle, and
adjustable ratchet that ensures full contact crimping.
The tool frame holds a die assembly with two
crimping chambers. See Figure 1.
The die assembly features a wire anvil, insulation
anvil, wire crimper, and insulation crimper.
Die retaining pins and die retaining screws are used
to position and secure the dies in the tool frame.
Attached to the outside of the frame is a locator
assembly, which contains a locator and contact
retainer. A nut is used on the upper die retaining
screw to hold the locator assembly in place.
Size Range
(AWG)
28--24
24--20
Stationary Jaw
Pivot Pin
Insulation Diameter (Max)
PRO- - CRIMPER III Hand Crimping
Tool Frame 354940- - 1 (408- - 9930)
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com
1.02 [.040]
1.52 [.060]
(mm [in.])
Back of Tool
(Wire Side)
Movable Handle
Wire
Stationary Handle
Instruction Sheet
408- - 9357
10 Mar 11 Rev E
Strip Length
2 54 [ 100]
2.54 [.100]
(mm [in.])
1 of 5
LOC B

58448-3 Summary of contents

Page 1

... Contact the Tooling Assistance Center or Product Information at the numbers listed below for specific contact part numbers. 1. INTRODUCTION PRO--CRIMPER III Hand Crimping Tool Assembly 58448--2 consists of Die Assembly 58448--3 and PRO--CRIMPER III Hand Crimping Tool Frame 354940--1. The die assembly consists of crimping dies and a locator assembly ...

Page 2

Nut Locator Chamfered Edge Wire Crimper Offset Wire Anvil Insulation Anvil 3. INSTALLATION AND REMOVAL OF DIE ASSEMBLY AND LOCATOR ASSEMBLY (Figure 2) 1. Open the tool handles, and remove the two die retaining screws from the tool jaws. 2. ...

Page 3

Hold the tool so that the front (locator side) is facing you. Squeeze tool handles together and allow them to open fully. 2. Insert the contact—mating end first—into the hole in the locator which corresponds with the appropriate crimping ...

Page 4

... Order repair kit and replaceable parts through your TE representative, or call 1--800--526--5142, or send a facsimile of your purchase order to 717--986--7605, or write to: CUSTOMER SERVICE (38--35) TYCO ELECTRONICS PO BOX 3608 HARRISBURG PA 17105--3608 10. REVISION SUMMARY Revisions to this instruction sheet include: Updated document to corporate requirements. ...

Page 5

... Die Assembly 58448- 3 Can Be Used In the Following Tools: PRO- CRIMPER III Hand Tool 354940- 1 (Instruction Sheet 408- 9930) SDE Bench Terminator 1490076- 2 (Customer Manual 409- 10052) Battery Tool (Shouldered Die) 1725837 (Customer Manual 409- 10053) Rev E SDE PEW- 12 Hand Tool 9- 1478240- 0 ...