CS42528-CQ Cirrus Logic Inc, CS42528-CQ Datasheet - Page 40
![IC, AUDIO CODEC, 24BIT, 192KHZ, LQFP-64](/photos/19/0/190013/4243363_sml.jpg)
CS42528-CQ
Manufacturer Part Number
CS42528-CQ
Description
IC, AUDIO CODEC, 24BIT, 192KHZ, LQFP-64
Manufacturer
Cirrus Logic Inc
Datasheet
1.CS42528-CQZ.pdf
(91 pages)
Specifications of CS42528-CQ
Audio Codec Type
Stereo
No. Of Adcs
2
No. Of Dacs
8
No. Of Input Channels
2
No. Of Output Channels
8
Adc / Dac Resolution
24bit
Adcs / Dacs Signal To Noise Ratio
114dB
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
CS42528-CQ
Manufacturer:
CIRRUS
Quantity:
20 000
Company:
Part Number:
CS42528-CQZ
Manufacturer:
Cirrus Logic Inc
Quantity:
135
Company:
Part Number:
CS42528-CQZ
Manufacturer:
CRYSTAL
Quantity:
850
Company:
Part Number:
CS42528-CQZ
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
Part Number:
CS42528-CQZ
Manufacturer:
CRIIUS
Quantity:
20 000
Company:
Part Number:
CS42528-CQZR
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
Part Number:
CS42528-CQZR
Manufacturer:
CIRRUS
Quantity:
20 000
40
4.8
4.9
Interrupts
The CS42528 has a comprehensive interrupt capability. The INT output pin is intended to drive the interrupt
input pin on the host microcontroller. The INT pin may be set to be active low, active high or active low with
no active pull-up transistor. This last mode is used for active low, wired-OR hook-ups, with multiple periph-
erals connected to the microcontroller interrupt input pin.
Many conditions can cause an interrupt, as listed in the interrupt status register descriptions (see
Status (address 20h) (Read Only)” on page
In addition, each source may be set to rising edge, falling edge, or level-sensitive. Combined with the option
of level-sensitive or edge-sensitive modes within the microcontroller, many different configurations are pos-
sible, depending on the needs of the equipment designer.
Reset and Power-Up
Reliable power-up can be accomplished by keeping the device in reset until the power supplies, clocks and
configuration pins are stable. It is also recommended that reset be activated if the analog or digital supplies
drop below the recommended operating condition to prevent power-glitch-related issues.
When RST is low, the CS42528 enters a low-power mode and all internal states are reset, including the
control port and registers, and the outputs are muted. When RST is high, the control port becomes opera-
tional, and the desired settings should be loaded into the control registers. Writing a 0 to the PDN bit in the
Power Control Register will then cause the part to leave the low-power state and begin operation. If the in-
ternal PLL is selected as the clock source, the serial audio outputs will be enabled after the PLL has settled
(see
The delta-sigma modulators settle in a matter of microseconds after the analog section is powered, either
through the application of power or by setting the RST pin high. However, the voltage reference will take
much longer to reach a final value due to the presence of external capacitance on the FILT+ pin. A time
delay of approximately 80 ms is required after applying power to the device or after exiting a reset state.
During this voltage reference ramp delay, all serial ports and DAC outputs will be automatically muted.
Setting the auto increment bit in the MAP allows successive reads or writes of consecutive registers. Each
byte is separated by an acknowledge bit.
“Power Control (address 02h)” on page 47
Send start condition.
Send 10011xx1(chip address & read operation).
Receive acknowledge bit.
Receive byte, contents of selected register.
Send acknowledge bit.
Send stop condition.
63). Each source may be masked off through mask register bits.
for more details).
CS42528
DS586F1
“Interrupt