LAN9215-MT SMSC, LAN9215-MT Datasheet - Page 82

• Manufacturer Part Number: LAN9215-MT
• Description: CONTROLLER, ENET, NON-PCI, 100TQFP
• Manufacturer: SMSC

Specifications of LAN9215-MT

• Data Rate: 100Mbps
• No. Of Ports: 2
• Ethernet Type: IEEE 802.3 / 802.3u
• Supply Current: 40mA
• Supply Voltage Range: 2.97V To 3.63V
• Operating Temperature Range: 0°C To +70°C
• Digital Ic Case Style: TQFP
• Interface Type: HBI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Revision 1.93 (12-12-07)
5.3.9
31-25
23-22
16-19
15-14
BITS
24
21
20
Reserved
AMDIX_EN Strap State. This read-only bit reflects the state of the
AMDIX_EN strap pin (pin 73). This pin can be overridden by PHY Registers
27.15 and 27.13
Reserved
Transmit Threshold Mode (TTM). This bit is used to control the transmit
threshold the MIL uses as shown in the two tables in the TR field of this
register. This bit is ignored when the SF bit is set (1).
This bit should be set to '1' when operating in 10Mbps mode, and cleared
to '0' when operating in 100Mbps mode if the SF bit cleared.
Store and Forward (SF). When set, this bit instructs the MIL to store a
frame of transmit data in the MIL buffer before forwarding to its final
destination.
If this bit is set, the MIL buffers the entire frame before transmitting. TTM
and TR (see bits 21,13, and 12) are treated as Don’t Cares once the SF
mode is selected.
If this bit is reset, the MAC initiates transmission before it receives the entire
frame from the HBI (Host Bus Interface). TTM and TR (see bit 21,13, and
12) determine when the MIL initiates the transmission. If the host cannot
keep up with the MAC transmitting the Ethernet Packet, there is a risk of an
Underrun Error.
TX FIFO Size (TX_FIF_SZ). Sets the size of the TX FIFOs in 1KB values
to a maximum of 14KB. The TX Status FIFO consumes 512 bytes of the
space allocated by TX_FIF_SIZ, and the TX data FIFO consumes the
remaining space specified by TX_FIF_SZ. The minimum size of the TX
FIFOs is 2KB (TX data and status combined). The TX data FIFO is used for
both TX data and TX commands.
The RX Status and data FIFOs consume the remaining space, which is
equal to 16KB – TX_FIF_SIZ. See
Configurable FIFO Memory Allocation," on page 85
Reserved
HW_CFG—Hardware Configuration Register
Note: The transmitter and receiver must be stopped before writing to this register. Refer to
Offset:
3.12.9, "Stopping and Starting the Transmitter," on page 55
Starting the Receiver," on page 60
DESCRIPTION
Highly Efficient Single-Chip 10/100 Ethernet Controller with HP Auto-MDIX and Industrial Temperature Support
74h
Section 5.3.9.1, "Allowable settings for
DATASHEET
82
for details on stopping the transmitter and receiver.
for more information.
Size:
and
32 bits
Section 3.13.4, "Stopping and
TYPE
R/W
R/W
R/W
RO
RO
RO
RO
SMSC
DEFAULT
AMDIX
Strap
LAN9215i
Pin
Datasheet
5h
0
0
-
-
Section