ISPPAC-POWR1014A-01TN48I LATTICE SEMICONDUCTOR, ISPPAC-POWR1014A-01TN48I Datasheet - Page 41

• Manufacturer Part Number: ISPPAC-POWR1014A-01TN48I
• Description: IC, POWER SUPPLY MONITOR, 48TQFP
• Manufacturer: LATTICE SEMICONDUCTOR
• Series: IspPACr

Specifications of ISPPAC-POWR1014A-01TN48I

• No. Of Macrocells: 24
• Frequency: 25MHz
• Supply Voltage Range: 2.8V To 3.96V
• Operating Temperature Range: -40°C To +105°C
• Logic Case Style: TQFP
• No. Of Pins: 48
• Svhc: No SVHC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Lattice Semiconductor
PLD_VERIFY – This instruction is used to read the content of the selected PLD AND/ARCH array column. This
specific column is preselected by using PLD_ADDRESS_SHIFT instruction. This instruction also forces the outputs
into the OUTPUTS_HIGHZ.
DISCHARGE – This instruction is used to discharge the internal programming supply voltage after an erase or pro-
gramming cycle and prepares ispPAC-POWR1014/A for a read cycle. This instruction also forces the outputs into
the OUTPUTS_HIGHZ.
CFG_ADDRESS – This instruction is used to set the address of the CFG array for subsequent program or read
operations. This instruction also forces the outputs into the OUTPUTS_HIGHZ.
CFG_DATA_SHIFT – This instruction is used to shift data into the CFG register prior to programming or reading.
This instruction also forces the outputs into the OUTPUTS_HIGHZ.
CFG_ERASE – This instruction will bulk erase the CFG array. The action occurs at the second rising edge of TCK
in Run-Test-Idle JTAG state. The device must already be in programming mode (PROGRAM_ENABLE instruction).
This instruction also forces the outputs into the OUTPUTS_HIGHZ.
CFG_PROGRAM – This instruction programs the selected CFG array column. This specific column is preselected
by using CFG_ADDRESS instruction. The programming occurs at the second rising edge of the TCK in Run-Test-
Idle JTAG state. The device must already be in programming mode (PROGRAM_ENABLE instruction). This
instruction also forces the outputs into the OUTPUTS_HIGHZ.
CFG_VERIFY – This instruction is used to read the content of the selected CFG array column. This specific col-
umn is preselected by using CFG_ADDRESS instruction. This instruction also forces the outputs into the
OUTPUTS_HIGHZ.
BULK_ERASE – This instruction will bulk erase all E
POWR1014/A. The device must already be in programming mode (PROGRAM_ENABLE instruction). This instruc-
tion also forces the outputs into the OUTPUTS_HIGHZ.
OUTPUTS_HIGHZ – This instruction turns off all of the open-drain output transistors. Pins that are programmed as
FET drivers will be placed in the active low state. This instruction is effective after Update-Instruction-Register
JTAG state.
PROGRAM_ENABLE – This instruction enables the programming mode of the ispPAC-POWR1014/A. This
instruction also forces the outputs into the OUTPUTS_HIGHZ.
IDCODE – This instruction connects the output of the Identification Code Data Shift (IDCODE) Register to TDO
(Figure 2-33), to support reading out the identification code.
Figure 2-33. IDCODE Register
PROGRAM_DISABLE – This instruction disables the programming mode of the ispPAC-POWR1014/A. The Test-
Logic-Reset JTAG state can also be used to cancel the programming mode of the ispPAC-POWR1014/A.
UES_READ – This instruction both reads the E
between the TDI and TDO pins (as shown in Figure 2-30), to support programming or reading of the user electronic
signature bits.
Bit
31
Bit
30
Bit
29
Bit
28
Bit
27
2
CMOS bits into the UES register and places the UES register
2-41
2
CMOS bits (CFG, PLD, UES, and ESF) in the ispPAC-
Bit
4
ispPAC-POWR1014/A Data Sheet
Bit
3
Bit
2
Bit
1
Bit
0
TDO