CAT28C256GI-15 CATALYST SEMICONDUCTOR, CAT28C256GI-15 Datasheet
![IC, EEPROM, 256KBIT, PARALLEL, LCC-32](/photos/19/4/190490/4243226_sml.jpg)
CAT28C256GI-15
Specifications of CAT28C256GI-15
Available stocks
Related parts for CAT28C256GI-15
CAT28C256GI-15 Summary of contents
Page 1
CAT28C256 256 kb Parallel EEPROM Description The CAT28C256 is a fast, low power, 5 V−only CMOS Parallel EEPROM organized as 32K x 8−bits. It requires a simple interface for in−system programming. On−chip address and data latches, self−timed write cycle with ...
Page 2
DIP Package (P, L) PLCC Package ( ...
Page 3
Table 1. ABSOLUTE MAXIMUM RATINGS Parameters Temperature Under Bias Storage Temperature Voltage on Any Pin with Respect to Ground (Note 1) V with Respect to Ground CC Package Power Dissipation Capability (T Lead Soldering Temperature (10 secs) Output Short Circuit ...
Page 4
Table 4. MODE SELECTION Mode Read Byte Write (WE Controlled) Byte Write (CE Controlled) Standby and Write Inhibit Read and Write Inhibit Table 5. CAPACITANCE (T = 25° 1.0 MHz Symbol C (Note 7) Input/Output Capacitance ...
Page 5
Table 7. A.C. CHARACTERISTICS, WRITE CYCLE Symbol t Write Cycle Time WC t Address Setup Time AS t Address Hold Time Setup Time Hold Time CH t (Note 10) CE Pulse Time CW t ...
Page 6
DEVICE OPERATION Read Data stored in the CAT28C256 is transferred to the data bus when WE is held high, and both OE and CE are held low. The data bus is set to a high impedance state when either CE ...
Page 7
Page Write The page write mode of the CAT28C256 (essentially an extended BYTE WRITE mode) allows from bytes of data to be programmed within a single EEPROM write cycle. This effectively reduces the byte−write time by a ...
Page 8
DATA Polling DATA polling is provided to indicate the completion of write cycle. Once a byte write or page write cycle is initiated, attempting to read the last byte written will output the complement of that data on I/O indeterminate) ...
Page 9
Hardware Data Protection The following is a list of hardware data protection features that are incorporated into the CAT28C256 sense provides for write protection when V CC falls below 3.5 V min power on delay mechanism, ...
Page 10
To activate the software data protection, the device must be sent three write commands to specific addresses with specific data (Figure 10). This sequence of commands (along with subsequent writes) must adhere to the page write timing specifications (Figure 12). ...
Page 11
PIN#1 IDENTIFICATION D1 D TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. (2) Complies with JEDEC MS-016. PACKAGE DIMENSIONS PLCC 32 CASE 776AK−01 ISSUE SYMBOL ...
Page 12
D1 PIN 1 D TOP VIEW q1 q SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MS-183. PACKAGE DIMENSIONS TSOP 28, 8x13.4 CASE 318AE−01 ISSUE SYMBOL ...
Page 13
D TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. (2) Complies with JEDEC MS-011. PACKAGE DIMENSIONS PDIP−28, 600 mils CASE 646AE−01 ISSUE A SYMBOL ...
Page 14
Example of Ordering Information Prefix Device # CAT 28C256 Company ID Product Number (Optional) 28C256 Package P: PDIP (Note 17) N: PLCC (Note 17) T13: TSOP ( 13.4 mm) (Note 17) L: PDIP (Lead Free, Halogen Free) G: ...