AM29F040B-70EF Spansion Inc., AM29F040B-70EF Datasheet - Page 14
![IC, FLASH, 40MBIT, 70NS, TSOP-32](/photos/19/5/190511/4434963_sml.jpg)
AM29F040B-70EF
Manufacturer Part Number
AM29F040B-70EF
Description
IC, FLASH, 40MBIT, 70NS, TSOP-32
Manufacturer
Spansion Inc.
Specifications of AM29F040B-70EF
Memory Type
Flash
Memory Size
40Mbit
Memory Configuration
512K X 8
Access Time
70ns
Supply Voltage Range
4.5V To 5.5V
Memory Case Style
TSOP
No. Of Pins
32
Cell Type
NOR
Density
4Mb
Access Time (max)
70ns
Interface Type
Parallel
Boot Type
Not Required
Address Bus
19b
Operating Supply Voltage (typ)
5V
Operating Temp Range
-40C to 85C
Package Type
TSOP
Program/erase Volt (typ)
4.5 to 5.5V
Sync/async
Asynchronous
Operating Temperature Classification
Industrial
Operating Supply Voltage (min)
4.5V
Operating Supply Voltage (max)
5.5V
Word Size
8b
Number Of Words
512K
Supply Current
30mA
Mounting
Surface Mount
Pin Count
32
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AM29F040B-70EF
Manufacturer:
VICOR
Quantity:
43
Part Number:
AM29F040B-70EF
Manufacturer:
AMD
Quantity:
20 000
Timer”
edge of the final WE# pulse in the command sequence.
Once the sector erase operation has begun, only the
Erase Suspend command is valid. All other commands
are ignored.
When the Embedded Erase algorithm is complete, the
device returns to reading array data and addresses are
no longer latched. The system can determine the sta-
tus of the erase operation by using DQ7, DQ6, or DQ2.
Refer to
these status bits.
Figure
tion. Refer to the Erase/Program Operations tables in
the
the Sector Erase Operations Timing diagram for timing
waveforms.
Erase Suspend/Erase Resume Commands
The Erase Suspend command allows the system to in-
terrupt a sector erase operation and then read data
from, or program data to, any sector not selected for
erasure. This command is valid only during the sector
erase operation, including the 50 µs time-out period
during the sector erase command sequence. The
Erase Suspend command is ignored if written during
the chip erase operation or Embedded Program algo-
rithm. Writing the Erase Suspend command during the
Sector Erase time-out immediately terminates the
time-out period and suspends the erase operation. Ad-
dresses are “don’t-cares” when writing the Erase
Suspend command.
When the Erase Suspend command is written during a
sector erase operation, the device requires a maximum
of 20 µs to suspend the erase operation. However,
when the Erase Suspend command is written during
the sector erase time-out, the device immediately ter-
minates the time-out period and suspends the erase
operation.
After the erase operation has been suspended, the
system can read array data from or program data to
any sector not selected for erasure. (The device “erase
suspends” all sectors selected for erasure.) Normal
read and write timings and command definitions apply.
Reading at any address within erase-suspended sec-
tors produces status data on DQ7–DQ0. The system
can use DQ7, or DQ6 and DQ2 together, to determine
if a sector is actively erasing or is erase-suspended.
See
status bits.
After an erase-suspended program operation is com-
plete, the system can once again read array data within
non-suspended sectors. The system can determine
12
“AC Characteristics”
“Write Operation Status”
2
section.) The time-out begins from the rising
“Write Operation Status”
illustrates the algorithm for the erase opera-
section for parameters, and to
for information on these
for information on
D A T A
Am29F040B
S H E E T
the status of the program operation using the DQ7 or
DQ6 status bits, just as in the standard program oper-
ation. See
information.
The system may also write the autoselect command
sequence when the device is in the Erase Suspend
mode. The device allows reading autoselect codes
even at addresses within erasing sectors, since the
codes are not stored in the memory array. When the
device exits the autoselect mode, the device reverts to
the Erase Suspend mode, and is ready for another
valid operation. See
for more information.
The system must write the Erase Resume command
(address bits are “don’t care”) to exit the erase suspend
mode and continue the sector erase operation. Further
writes of the Resume command are ignored. Another
Erase Suspend command can be written after the de-
vice has resumed erasing.
Notes:
1. See the appropriate Command Definitions table for erase
2. See
command sequence.
“DQ3: Sector Erase Timer”
No
Command Sequence
Figure 2. Erase Operation
“Wr ite Operation Status”
Erasure Completed
Write Erase
from System
Data = FFh?
Data Poll
START
“Autoselect Command Sequence”
Yes
for more information.
21445E7 August 3, 2009
Embedded
Erase
algorithm
in progress
for more