LM2940CT-5.0 National Semiconductor, LM2940CT-5.0 Datasheet - Page 14

IC, LDO VOLT REG, 5V, 1A, TO-220

LM2940CT-5.0

Manufacturer Part Number
LM2940CT-5.0
Description
IC, LDO VOLT REG, 5V, 1A, TO-220
Manufacturer
National Semiconductor
Datasheet

Specifications of LM2940CT-5.0

Primary Input Voltage
26V
Output Voltage Fixed
5V
Dropout Voltage Vdo
500mV
No. Of Pins
3
Output Current
1A
Operating Temperature Range
0°C To +125°C
Termination Type
Through Hole
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LM2940CT-5.0
Manufacturer:
NS
Quantity:
9 999
Part Number:
LM2940CT-5.0
Manufacturer:
LT
Quantity:
232
Part Number:
LM2940CT-5.0
Manufacturer:
NS
Quantity:
1 000
Part Number:
LM2940CT-5.0
Manufacturer:
TI
Quantity:
1 000
Part Number:
LM2940CT-5.0
Manufacturer:
NS
Quantity:
21
Part Number:
LM2940CT-5.0
Manufacturer:
NS
Quantity:
76
Part Number:
LM2940CT-5.0
Manufacturer:
TI/NS
Quantity:
12 000
Part Number:
LM2940CT-5.0
Manufacturer:
NS/国半
Quantity:
20 000
Part Number:
LM2940CT-5.0/NOPB
Manufacturer:
TI/德州仪器
Quantity:
20 000
Part Number:
LM2940CT-5.0/NOPB
0
Part Number:
LM2940CT-5.0P+
Manufacturer:
AD
Quantity:
1 430
www.national.com
   θ
When a value for θ
heatsink must be selected that has a value that is less than
or equal to this number.
θ
in the catalog, or shown in a curve that plots temperature rise
vs power dissipation for the heatsink.
HEATSINKING TO-263 PACKAGE PARTS
The TO-263 (“S”) package uses a copper plane on the PCB
and the PCB itself as a heatsink. To optimize the heat sinking
ability of the plane and PCB, solder the tab of the package to
the plane.
Figure 3 shows for the TO-263 the measured values of θ
for different copper area sizes using a typical PCB with 1
ounce copper and no solder mask over the copper area used
for heatsinking.
FIGURE 3. θ
As shown in the figure, increasing the copper area beyond 1
square inch produces very little improvement. It should also
be observed that the minimum value of θ
package mounted to a PCB is 32°C/W.
As a design aid, Figure 4 shows the maximum allowable pow-
er dissipation compared to ambient temperature for the
TO-263 device. This assumes a θ
inch of 1 ounce copper and a maximum junction temperature
(T
(H−A)
J
) of 125°C.
is specified numerically by the heatsink manufacturer
(C−H)
(JA)
is defined as the thermal resistance between
the case and the surface of the heatsink. The
value of θ
about 2.5°C/W (depending on method of at-
tachment, insulator, etc.). If the exact value is
unknown, 2°C/W should be assumed for θ
−H)
vs. Copper (1 ounce) Area for the TO-263
.
(H−A)
is found using the equation shown, a
(C−H)
Package
will vary from about 1.5°C/W to
(JA)
of 35°C/W for 1 square
(JA)
for the TO-263
882238
(JA)
(C
14
HEATSINKING SOT-223 PACKAGE PARTS
The SOT-223 (“MP”) packages use a copper plane on the
PCB and the PCB itself as a heatsink. To optimize the heat
sinking ability of the plane and PCB, solder the tab of the
package to the plane.
Figure 5 and Figure 6 show the information for the SOT-223
package. Figure 6 assumes a θ
inch of 1 ounce copper and 51°C/W for 1 square inch of 2
ounce copper, with a maximum ambient temperature (T
85°C and a maximum junction temperature (T
For techniques for improving the thermal resistance and pow-
er dissipation for the SOT-223 package, please refer to Ap-
plication Note AN-1028.
FIGURE 5. θ
FIGURE 4. Maximum Power Dissipation vs. T
(JA)
vs. Copper (2 ounce) Area for the SOT-223
TO-263 Package
Package
(JA)
of 74°C/W for 1 square
882240
J
) of 125°C.
882239
A
for the
A
) of

Related parts for LM2940CT-5.0