A1205LUA-T Allegro Microsystems Inc, A1205LUA-T Datasheet - Page 7

• Manufacturer Part Number: A1205LUA-T
• Description: HALL EFFECT BIPOLAR SWITCH
• Manufacturer: Allegro Microsystems Inc
• Type: Bipolar Latchr

Specifications of A1205LUA-T

• Rohs Compliant: YES
• Sensing Range: 50G Trip, -50G Release
• Voltage - Supply: 3.8 V ~ 24 V
• Current - Supply: 7.5mA
• Current - Output (max): 25mA
• Output Type: Digital, Open Drain
• Operating Temperature: -40°C ~ 150°C
• Package / Case: 3-SIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

A1205
Bipolar Device Switching
The devices of the A120X family provide highly sensitive
switching for applications using magnetic fields of alternating
polarities, such as ring magnets. There are three switching modes
for bipolar devices, referred to as latch, unipolar switch, and
negative switch. Mode is determined by the switchpoint charac-
teristics of the individual device. The characteristic hysteresis,
B
strength and polarity of the switchpoints of the device. (Note
that, in the following descriptions, a negative magnetic value
indicates a north polarity field, and a positive magnetic value
indicates a south polarity field. For a given value of magnetic
strength, B
strength, but opposite polarity. B = 0 indicates the absence of a
magnetic field.)
Bipolar devices typically behave as latches. In this mode,
magnetic fields of opposite polarity and equivalent strengths
are needed to switch the output. When the magnetic fields are
removed (B  0) the device remains in the same state until a
magnetic field of the opposite polarity and of sufficient strength
causes it to switch. The hysteresis of latch mode behavior is
shown in panel A of figure 1.
Figure 1. Bipolar Device Output Switching Modes. These behaviors can be exhibited when using a circuit such as that shown in panel D. Panel A
displays the hysteresis when a device exhibits latch mode (note that the B
B
such as the 120x family, can operate in any of the three modes.
HYS
HYS
band is more positive than B = 0), and panel C shows negative switch behavior (the B
, of the device, is the difference in the relative magnetic
V+
0
B–
X
, the values –B
B
(A)
HYS
0
X
and B
B+
V
V
CC
X
OUT(SAT)
indicate two fields of equal
Functional Description
V+
0
B– 0
B
(B)
HYS
HYS
Continuous-Time Bipolar Switch
band incorporates B= 0), panel B shows unipolar switch behavior (the
In contrast to latching, when a device exhibits unipolar switch-
ing, it only responds to a south magnetic field. The field must
be of sufficient strength, > B
the field is reduced beyond the B
back to the high state, as shown in panel B of figure 1. Devices
exhibiting negative switch behavior operate in a similar but
opposite manner. A north polarity field of sufficient strength,
> B
the result is that V
RP
V
S
, (more north than B
B+
V
V
CC
OUT(SAT)
HYS
band is more negative than B = 0). Bipolar devices,
OUT
switches high, as shown in panel C. When
A120x
V+
0
RP
115 Northeast Cutoff
1.508.853.5000; www.allegromicro.com
Allegro MicroSystems, Inc.
Worcester, Massachusetts 01615-0036 U.S.A.
B–
VCC
GND
OP
(D)
) is required for operation, although
, for the device to operate. When
RP
VOUT
level, the device switches
B
(C)
HYS
R
L
0
Output
B+
V
V
CC
OUT(SAT)
7