CS61884-IQZ Cirrus Logic Inc, CS61884-IQZ Datasheet - Page 25
![no-image](/images/manufacturer_photos/0/1/141/cirrus_logic_inc_sml.jpg)
CS61884-IQZ
Manufacturer Part Number
CS61884-IQZ
Description
IC,PCM TRANSCEIVER,OCTAL,CEPT PCM-30/E-1,QFP,144PIN,PLASTIC
Manufacturer
Cirrus Logic Inc
Specifications of CS61884-IQZ
Rohs Compliant
YES
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CS61884-IQZ
Manufacturer:
CIRRUS
Quantity:
60
Company:
Part Number:
CS61884-IQZ
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
Part Number:
CS61884-IQZ
Manufacturer:
CIRRUS
Quantity:
20 000
Company:
Part Number:
CS61884-IQZR
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
The CS61884 also allows the user to customize the
transmit pulse shapes to compensate for non-stan-
dard cables, transformers, or protection circuitry.
For further information on the AWG Refer to
bitrary Waveform Generator
page 43).
For more information on the host mode registers,
refer to
page 35).
9.1 Bipolar Mode
Bipolar mode provides transparent operation for
applications in which the line coding function is
performed by an external framing device. In this
mode, the falling edge of TCLK samples NRZ data
on TPOS/TNEG for transmission on TTIP/TRING.
9.2 Unipolar Mode
In unipolar mode, the CS61884 is configured such
that transmit data is encoded using B8ZS, HDB3,
or AMI line codes. This mode is activated by hold-
ing TNEG/UBS “High” for more than 16 TCLK
cycles. Transmit data is input to the part via the
TPOS/TDATA pin on the falling edge of TCLK.
When operating the part in hardware mode, the
CODEN pin is used to select between B8ZS/HDB3
or AMI encoding. During host mode operation, the
line coding is selected via the
ister (0Fh)
NOTE: The encoders/decoders are selected for all
DS485F1
eight channels in both hardware and host
mode.
Register Descriptions
(See Section 14.16 on page 38).
LEN[2:0]
000
001
010
011
100
101
110
111
Table 5. Hardware Mode Line Length Configuration Selection
Transmit Pulse Configuration
DS1, Option A (undershoot)
Global Control Reg-
DSX-1: 133-266 ft. (1.2dB)
DSX-1: 266-399 ft. (1.8dB)
DSX-1: 399-533 ft. (2.4dB)
DSX-1: 533-655 ft. (3.0dB)
DSX-1: 0-133 ft. (0.6dB)
(See Section 14 on
(See Section 15 on
DS1, Option A (0 dB)
E1 3.0V / E1 2.37V
Ar-
9.3 RZ Mode
In RZ mode, the internal pulse shape circuitry is
bypassed and RZ data driven into TPOS/TNEG is
transmitted on TTIP/TRING. In this mode, the
pulse width of the transmitter output is determined
by the width of the RZ signal input to
TPOS/TNEG. This mode is entered when MCLK
does not exist and TCLK is held “High” for at least
12 µsec.
9.4 Transmitter Powerdown / High-Z
The transmitters can be forced into a high imped-
ance, low power state by holding TCLK of the ap-
propriate channel low for at least 12µs or 140
MCLK cycles. In hardware and host mode, the
TXOE pin forces all eight transmitters into a high
impedance state within 1µs.
In host mode, each transmitter is individually con-
trollable using the
(See Section 14.19 on page 39). The TXOE pin can
be used in host mode, but does not effect the con-
tents of the Output Enable Register. This feature is
useful in applications that require redundancy.
9.5 Transmit All Ones (TAOS)
When TAOS is activated, continuous ones are
transmitted on TTIP/TRING using MCLK as the
transmit timing reference. In this mode, the TPOS
and TNEG inputs are ignored.
In hardware mode, TAOS is activated by pulling
TCLK “High” for more than 16 MCLK cycles.
120Ω / 75Ω
Line Z
100Ω
100Ω
100Ω
100Ω
100Ω
100Ω
100Ω
Output Disable Register (12h)
Operation
T1/J1
T1/J1
T1/J1
T1/J1
T1/J1
T1/J1
T1/J1
E1
CS61884
25