DSPIC30F6013A-20E/PT Microchip Technology, DSPIC30F6013A-20E/PT Datasheet - Page 2

• Manufacturer Part Number: DSPIC30F6013A-20E/PT
• Description: Digital Signal Processor
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F6013A-20E/PT

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 68
• Program Memory Size: 132KB (44K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 6K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 80-TFQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM300024 - KIT DEMO DSPICDEM 1.1XLT80PT3 - SOCKET TRAN ICE 80MQFP/TQFPAC164320 - MODULE SKT MPLAB PM3 80TQFPAC30F007 - MODULE SKT FOR DSPIC30F 80TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

dsPIC30F6011A/6012A/6013A/6014A
8.
9.
10. I
11. I
12. I
The following sections describe the errata and work
around to these errata, where they may apply.
DS80303E-page 2
PLL Lock Status Bit
The PLL LOCK Status bit (OSCCON<5>) can
occasionally get cleared and generate an
oscillator failure trap even when the PLL is still
locked and functioning correctly.
PSV Operations
An address error trap occurs in certain addressing
modes when accessing the first four bytes of any
PSV page.
The 10-bit slave does not set the RBF flag or load
the I2CxRCV register, on address match if the
Least Significant bits of the address are the same
as the 7-bit reserved addresses.
When the I
slave with an address of 0x102, the I2CxRCV
register content for the lower address byte is 0x01
rather than 0x02.
When the I
device generates a glitch on the SDA and SCL
pins, causing a false communication start in a
single-master configuration or a bus collision in a
multi-master configuration.
2
2
2
C Module: 10-bit Addressing Mode
C Module: 10-bit Addressing Mode
C Module
2
2
C module is enabled, the dsPIC
C module is configured as a 10-bit
®
DSC
1. Module: CPU –
EXAMPLE 1:
2. Module: Output Compare in PWM Mode
L0:daw.b
L1: ....
The Decimal Adjust instruction, DAW.b, may
improperly clear the Carry bit, C (SR<0>), when
executed.
Work around
Check the state of the Carry bit prior to executing
the DAW.b instruction. If the Carry bit is set, set the
Carry bit again after executing the DAW.b
instruction. Example 1 shows how the application
should process the Carry bit during a BCD addition
operation.
If the desired duty cycle is ‘0’ (OCxRS = 0), the
module will generate a high level glitch of 1 T
Additionally, on the next cycle after the glitch, the
OC pin does not go high, or, in other words, it
misses the next compare for any value written on
OCxRS.
Work around
There are two possible solutions to this problem:
1. Load a value greater than ‘0’ to the OCxRS
2. If the application requires 0% duty cycles, the
.include “p30fxxxx.inc”
.......
mov.b
mov.b
add.b
bra
daw.b
bset.b
bra
register when operating in PWM mode. In this
case, no 0% duty cycle is achievable.
output compare module can be disabled for
0% duty cycles, and re-enabled for non-zero
percent duty cycles.
#0x80, w0
#0x80, w1
w0, w1, w2 ;Perform addition
NC, L0
w2
L1
w2
SR, #C
DAW.b
CHECK CARRY BIT BEFORE
DAW.b
© 2008 Microchip Technology Inc.
;First BCD number
;Second BCD number
;If C set go to L0
;If not,do DAW and
;set the carry bit
;and exit
Instruction
CY
.