DSPIC30F6014AT-20E/PF Microchip Technology, DSPIC30F6014AT-20E/PF Datasheet - Page 88

• Manufacturer Part Number: DSPIC30F6014AT-20E/PF
• Description: 16-bit MCU/DSP 30MIPS 144KB 80 TQFP 14x14x1mm T/R
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F6014AT-20E/PF

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: AC'97, Brown-out Detect/Reset, I²S, LVD, POR, PWM, WDT
• Number Of I /o: 68
• Program Memory Size: 144KB (48K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 80-TQFP, 80-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM300024 - KIT DEMO DSPICDEM 1.1DM300019 - BOARD DEMO DSPICDEM 80L STARTERDM300004-2 - BOARD DEMO DSPICDEM.NET 2DM300004-1 - BOARD DEMO DSPICDEM.NET 1AC164314 - MODULE SKT FOR PM3 80PFAC30F001 - MODULE SOCKET DSPIC30F 80TQFPXLT80PT2 - SOCKET TRANSITION ICE 80TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

dsPIC30F6011A/6012A/6013A/6014A
13.5
When the CPU enters Sleep mode, all internal clocks
are stopped. Therefore, when the CPU enters the
Sleep state, the output compare channel will drive the
pin to the active state that was observed prior to
entering the CPU Sleep state.
For example, if the pin was high when the CPU entered
the Sleep state, the pin will remain high. Likewise, if the
pin was low when the CPU entered the Sleep state, the
pin will remain low. In either case, the output compare
module will resume operation when the device wakes
up.
13.6
When the CPU enters the Idle mode, the output
compare module can operate with full functionality.
The output compare channel will operate during the
CPU Idle mode if the OCSIDL bit (OCxCON<13>) is at
logic ‘0’ and the selected time base (Timer2 or Timer3)
is enabled and the TSIDL bit of the selected timer is set
to logic ‘0’.
DS70143E-page 88
Output Compare Operation During
CPU Sleep Mode
Output Compare Operation During
CPU Idle Mode
13.7
The output compare channels have the ability to gener-
ate an interrupt on a compare match, for whichever
Match mode has been selected.
For all modes except the PWM mode, when a compare
event occurs, the respective interrupt flag (OCxIF) is
asserted and an interrupt will be generated if enabled.
The OCxIF bit is located in the corresponding IFS
status register and must be cleared in software. The
interrupt is enabled via the respective compare inter-
rupt enable (OCxIE) bit located in the corresponding
IEC control register.
For the PWM mode, when an event occurs, the respec-
tive timer interrupt flag (T2IF or T3IF) is asserted and
an interrupt will be generated if enabled. The IF bit is
located in the IFS0 status register and must be cleared
in software. The interrupt is enabled via the respective
timer interrupt enable bit (T2IE or T3IE) located in the
IEC0 control register. The output compare interrupt flag
is never set during the PWM mode of operation.
Output Compare Interrupts
© 2011 Microchip Technology Inc.