DSPIC30F6014AT-20E/PF Microchip Technology, DSPIC30F6014AT-20E/PF Datasheet - Page 12

• Manufacturer Part Number: DSPIC30F6014AT-20E/PF
• Description: 16-bit MCU/DSP 30MIPS 144KB 80 TQFP 14x14x1mm T/R
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F6014AT-20E/PF

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: AC'97, Brown-out Detect/Reset, I²S, LVD, POR, PWM, WDT
• Number Of I /o: 68
• Program Memory Size: 144KB (48K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 80-TQFP, 80-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM300024 - KIT DEMO DSPICDEM 1.1DM300019 - BOARD DEMO DSPICDEM 80L STARTERDM300004-2 - BOARD DEMO DSPICDEM.NET 2DM300004-1 - BOARD DEMO DSPICDEM.NET 1AC164314 - MODULE SKT FOR PM3 80PFAC30F001 - MODULE SOCKET DSPIC30F 80TQFPXLT80PT2 - SOCKET TRANSITION ICE 80TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

dsPIC30F6011A/6012A/6013A/6014A
18. Module: LP Oscillator
19. Module: ADC
20. Module: PLL
DS80457B-page 12
The 32 kHz LP Oscillator module is not
operational for this version of silicon.
Work around
None.
Affected Silicon Revisions
ADC event triggers from the INT0 pin will not
wake-up the device from Sleep mode if the SMPI
bits are non-zero. This means that if the ADC is
configured to generate an interrupt after a certain
number of INT0 triggered conversions, the ADC
conversions will not be triggered and the device
will remain in Sleep. The ADC will perform
conversions and wake-up the device only if it is
configured to generate an interrupt after each INT0
triggered conversion (SMPI<3:0> = 0000).
Work around
None. If ADC event trigger from the INT0 pin is
required, initialize SMPI<3:0> to ‘0000’ (interrupt
on every conversion).
Affected Silicon Revisions
If 4x or 8x PLL mode is used, the input frequency
range is 5 MHz-10 MHz instead of 4 MHz-10 MHz.
Work around
None. If 4x or 8x PLL is used, make sure the input
crystal or clock frequency is 5 MHz or greater.
Affected Silicon Revisions
A2
A2
A2
X
X
X
B0
B0
B0
B1
B1
B1
21. Module: ADC
If the ADC module is in an enabled state when the
device enters Sleep mode as a result of executing
a PWRSAV #0 instruction, the device power-down
current (I
in the device data sheet. This may happen even if
the ADC module is disabled by clearing the ADON
bit prior to entering Sleep mode.
Work around
In order to remain within the I
listed in the device data sheet, the user software
must completely disable the ADC module by
setting the ADC Module Disable bit in the
corresponding Peripheral Module Disable (PMDx)
register, prior to executing a PWRSAV
instruction.
Affected Silicon Revisions
A2
X
B0
X
PD
) may exceed the specifications listed
B1
X
© 2010 Microchip Technology Inc.
PD
specifications
#0